5/6
Cat. No(s): 0 670 99 - 0 784 54 - 0 791 58L - 0 792 58 - 5 740 47/97
Switch sensor 3-wire - 2000 W
Technical data sheet: S000074408EN-3
Updated: 29/10/2020
Created: 17/12/2012
7.3 Detection parameters
Time delay: Length of time the load is on after detection.
Sensitivity: Detection range setting.
Modes:
Auto on/Auto off mode:
Comes on automatically:
- At the detection of a presence if there is an insufficient natural level
of light.
Turns off automatically:
- If no presence is detected and at the end of the time delay set.
- Or if the natural light level is sufficient (regulation activated)
Another detection causes automatic switch-on if there is insufficient
light.
Walk-through mode:
- If no presence is detected in the 20 seconds following an initial detec-
tion, the product will cut off the load after 3 minutes.
- If another presence is detected in the 3 minutes following initial detec-
tion, the device will cut off the load at the end of the set time delay.
Manual on/Auto off mode:
Comes on via a manual switch, automatic switch off:
- Where no presence is detected and at the end of the time delay set.
After switch-off, any new detection within a 30 second period triggers an
automatic switch-on. The Restart function must be activated.
After 30 seconds the device is switched on via a manual switch.
Detection system:
Initial detection: The load is switched on as soon as the first detection
occurs if the natural light level is below the light level threshold.
Maintain: The load remains active if another presence is detected.
Restard: In manual mode. After switch-off, any new detection within a
30 second period triggers an automatic switch-on.
After 30 seconds the device must be switched on manually.
Alarm: an audible signal is emitted before switch-off. (1 minute before,
then 30 seconds, then 10 seconds).
7. OPERATION
(continued)
7.4 Light parameters
Light level threshold: Value at which the load comes on if the
natural light level is less than the setting.
Advanced mode:
Calibration: The ambient light level measured with a luxme-
ter must then be transmitted to the sensor (see data sheet
Cat. No. 0 882 30).
Regulation : Automatic switch-off of the load 10 minutes after the
light level threshold is exceeded with an additional safety threshold
(to avoid lights switching off at the wrong moment).
Light contribution: Quantity of additional lux provided by the load
being switched on.
When the light contribution parameter is set to "Auto" (value 0) on the
configuration tool Cat. No. 0 882 30 the sensor automatically calculates
the light contribution.
7.5 Modifying the parameters using the configuration tools
• 0 882 35: Simplified configuration tool
• 0 882 30: Advanced configuration tool
When the sensor receives an IR command using the configuration tool,
it emits a beep acknowledging the modification.
For more information about setting parameters, refer to the data sheet
for the configuration tool Cat. No. 0 882 30.
Range: 1 m.
The potentiometers are active by default. Using a configuration tool
deactivates all the potentiometers.
Reset the product to reactivate them.
- Restore to factory settings:
1
st
press: Short press on LEARN: the LED flashes slowly.
2
nd
press: Press and hold down LEARN for 10 seconds until the LED
flashes quickly.
7. OPERATION
(continued)
Sensor parameters
Default
value
Modifiable
parameters
Configuration
tools
0 882 30 0 882 35
Light level threshold
300 lux
20, 100, 300,
500, 1000 lux
−
5 - 1275 lux
−
A
dv
anc
ed
mo
de
Calibration
−
0 - 99995 lux
−
Regulation
Actif
Activer/
Désactiver
−
Light
contribution
Auto
Auto - 1275 lux
−
Caution: At 1275 lux, the device becomes a motion sensor.
Sensor parameters
Default
value
Modifiable
parameters
Configuration
tools
0 882 30 0 882 35
Time delay
15 mn
3,5,10,15,20
min
−
5s - 59 min 59s
−
Sensivity
PIR
(very high)
Low, medium,
high, very high
Modes
Auto on/
Auto off
Active
Activate/
Deactivater
Walk-
through
mode
Inactivr
Activate/
Deactivate
Manual on/
Auto off
Inactir
Activate/
Deactivate
Detection system
Initial
PIR
Not modifiable
−
Maintain
PIR
Not modifiable
−
Restart
PIR
PIR ,
Deactivater
−
Alarm
Inactive
Activate/
Deactivate
−
