manualshive.com logo in svg

Legendfires Spirit Superslim, Installation And User Instructions Manual, Page: 7 / 16

Share
Download
Legendfires Spirit Superslim Installation And User Instructions Manual Download Page 7

TECHNICAL DATA

7

Gas Type

Natural Gas (G20) Cat 

I

2H

Gas Connection

8mm

Number of Injectors

One

Injector size

Stereomatic 065

Control Max Operating Temperature

80

o

c

Inlet Pressure Cold

20 mbar (8” W.G.)

Heat Input (Gross)

5.5 kW

Weight

10 kg

1. 

Front Coal & Fuel Bed

- All these ceramic components can be replaced at service intervals depending on

their condition. If the coals do require replacement, the consumer can do so provided that the Ceramic
Component Layout Instructions (pages 12-15) are adhered to. Only genuine Legend replacement parts should
be used.
Order Ref: 

SSFC02, SSCM03,

2. 

Oxygen Depletion Sensing Pilot

- In the unlikely event of a pilot failure, the pilot assembly should only be

replaced by a 

GAS SAFE Registered Engineer

. The user must not carry out this work.

Order Ref: 

LEG01

3. 

Control Tap

- In the unlikely event of control tap failure, the assembly should only be replaced by a 

GAS SAFE Registered Engineer

. The user must not carry out this work.

Order Ref: 

LEG11

REPLACEMENT PARTS

Summary of Contents for Spirit Superslim

















Reviews:

No comments