background image

11 

 

0x0D (13) 

Setup the wait time of PIR for clear the motion. 

Valid values: 0x05~0x3BC4 

0x001E 

0x0E (14) 

When the Motion Sensor is triggered, if this parameter is 

0x01 then it will send Basic set command to group 1. 

0 = Don't send. 

1 = Send. 

0x00 

0x0F (15) 

PIR triggers the correspondence between the value of the 
Basic set and the PIR state. 
-If this value is 0x00 : 
PIR triggers send the basic set with 0xFF, PIR alarm 
release send the basic set with 0x00. 
-If this value is 0x01 : 
PIR triggers send the basic set with 0x00, PIR alarm 
release send the basic set with 0xFF. 
Only support 0x00 and 0x01 values as valid value.

 

0x00 

0x10 (16) 

Motion detection sensitivity level is a value between 1 
and 10. This value affects the amount of motion energy 
required to generate a motion event and also affects the 
detection range and angle. 

1 = Lowest Motion Sensitivity 
10 = Highest Motion Sensitivity

 

 

0x09 

0x11 (17) 

Enable/disable pet immunity mode. This feature is lens 
dependent and detection range may be reduced 
when Pet Immunity is enabled. 

0 = Disable the 

pet immunity mode

 

1 = Enable the 

pet immunity mode 

0x01 

           

7.

 

Attention 

1.

 

If need to clean the sensor, please use a soft cloth with a little alcohol to wipe it after you cut off the 
power. 

2.

 

This product is just for indoor use. 

3.

 

Replace  the  battery  timely  on  low  battery  warning  to  ensure  the  detector  works  properly.  Please 
remove the battery and safe keeping, if you don’t use this product for a long time. 

4.

 

This device can be mounted on the wall only, it cannot be installed on the ceiling.   

5.

 

The reference range template of PIR detection is tested at the indoor temperature (the range is 20

℃~

25

)

the  target  of  the  test  is  77kg

±

10kg  weight  and  1.71m

±

0.3m  height,  the  target  of  the  test 

across movement speed is 4m/s

±

0.15m/s.   

6.

 

In order to prevent the PIR sensor’s abnormal fault, please don’t mounting and operating sensor in the 

bellow conditions, 

      Firstly, product mounting should prevent installed in the air flow environment such as in front of the 

door, window, heater, air conditioner and so on. 

Summary of Contents for 7C-SS-VA-H0













Reviews: