background image

3

 

 

 

3.

 

Specification

 

Detection Technology

 

Magnetic switch

 

Detective Range

 

20mm

 

Communication Protocol 

 

Z-Wave

 

Radio Frequency 

 

908.42MHz    (US)

 

868.42MHz    (EU)

 

921.42MHz    (AU)

 

Wireless Range

 

More than 100m outdoors

 

Approximately 30m indoors (depending

 

on building materials)

 

Power Source 

 

3V, CR2 *1

 

Battery Life 

 

2 years

 

Mounting

 

Screws or 3M Tape

 

Operating Temperature 

 

  -10°C to 45°C

 

Operating Humidity 

 

Up to 85% non-condensing

 

Certifications 

 

CE/FCC, Z-Wave Plus

 

Dimensions (mm):

 

68.4.(L)*24.4(W)*21.5(H) for Main Body

 

44.4(L)*15(W)*13(H)    for Magnetic Part

 

 

4.

 

Features/Capabilities:

 

 

1.

 

The LEEDARSON Door/Window Sensor contains a sensor body and a magnet.

 

 
2.

 

The LEEDARSON Door/Window Sensor detects through the separation and combination of the main 
body and the magnet.

 

     

 
3.

 

Recommend installation distance between the sensor body and the magnet is 10MM.

 

 

4.

 

The Sensor also anti-tamper functionality. Once the sensor is moved, it will notify the gateway.

 

 

5.

 

The LEEDARSON Door/Window Sensor is powered by CR2 battery with 2 years battery life.

 

 

6.

 

The LEEDARSON Door/Window Sensor is designed to be mounted on the door or windows.

 

 

7.

 

The LEEDARSON Door/Window Sensor supports low battery alarm function.

 

 

8.

 

The LEEDARSON Door/Window Sensor supports firmware OTA.

 

       

 

Summary of Contents for 7A-SS-VE-H0












Reviews: