GB
Operating Manual
Packaging contents:
1x Rechargable Multi-Function Light
1x USB Charging cable (1m)
1x Operating manual
I
mportant
: please read these instructions carefully.
Note the safe operational requirments, warnings and
cautions, use this product correctly and with care for
the purpose for which it is intended.Failure to do so
may cause damage and/or personal injury and will in-
validate the warranty. Please keep instructions safe for
future use.
1. SAFETY INSTRUCTIONS
1.1. GENERAL
•
Ensure the worklight is correctly charged before
initial use.
•
DO NOT cover or block the lens during use.
•
DO NOT shine directly into your, other person‘s or
animal‘s eyes.
•
DO NOT allow children to use the worklight
•
DO NOT handle or move the worklight whilst it is
being charged.
•
DO NOT use the worklight if you suspect that the
battery or the worklight casing is damaged.
•
Ensure replacement batteries are genuine batteries
of the same rating.
•
Ensure the worklight is unplugged and allowed to
cool before attempting any cleaning or replace-
ment.
•
When not in use, store the worklight in a safe, dry,
childproof location.
1.2 BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:
•
DO NOT attempt to open, disassemble, modify or
service the battery.
•
Ensure the charger is switched off and disconnected
from the worklight before attempting to open the
lamp unit.
•
DO NOT expose to temperatures above 60 °C
•
DO NOT crush, puncture, short external contacts or
dispose of in fire or water.
•
Replace only with the batteries designated for this
product.
•
Dispose of the old batteries in accordance with local
authority battery regulations. DO NOT dispose of
with regular refuse.
•
If the electrolyte in the cells contacts the skin, wash
thoroughly with soap and water.
•
If the electrolyte in the cells gets into the eyes, rinse
thoroughly with cool water and seek immediate
medical attention.
1.3 ELECTRICAL SAFETY
Use only a certified mains USB-charger plug (Max.
5V/1A) to connect the worklight to the mains power
supply. Or use a certified power adapter for connecting
to a vehicle‘s 12v -24v accessory socket. (Chargers not
included!)
Warning!
It is the user’s responsibility to read, under-
stand and comply with the following electrical instruc-
tions: You must ensure the risk of electric shock is mini-
mized by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be
incorporated in the main distribution board. We also
recommend that an RCD (Residual Current Device) is
used with all electrical products, particularly portable
equipment which is plugged into an electrical supply
not protected by an RCCB.
You must also read and understand the following in-
structions concerning electrical safety.
You must ensure that you:
•
Inspect the charger plug,cable and connector for
wear and damage to ensure items are safe before
connecting to the mains power supply. If worn or
damaged DO NOT use.
•
Check cables are always protected against short
circuit and overload.
•
Important: Check that the voltage marked on the
charger plug is the same as the power supply to be
used.
•
Uncoil the cable between charger and the work-
light.
•
DO NOT pull the charger plug from the mains socket
by the lead.
•
Make sure you use a 5VDC USB Charger (Not
included)
•
DO NOT place the connector into any area of the
worklight except the correct jack inlet socket.
2. INTRODUCTION
3 watt SMD + 1 watt LED rechargeable worklight,3W
COB to be used as an inspection lamp or 1W LED on the
top to be used as a torch. Magnets on the base and on
the rear, two 360 degree swivel hooks, Base pivots 180
degree.
Supplied without chargers, use only certified chargers
(5V, max. 1A).
3. OPERATION AND CHARGING
3.1 CHARGING
Warning
! Ensure that you read, and fully understand
the safety instructions before use.
3.1.1 Charge the batteries before use.
Important
: Ensure the worklight is turned „Off“ while
charging. Failure to do so will damage the charger plug/
vehicle plug.
3.1.2 Connect the USB charging plug into the micro-USB
charging socket, which is located on the rear of inspec-
tion lamp.
Then connect the USB charging cable to a suitable USB
charger (max 5V 1A, not included)
Connect the chosenUSB charger to a power supply.
3.1.3 The charging LED indicator will illuminate red,
charge for ~4 hours or until the charging LED illumi-
nates green.
3.1.4 Disconnect the charger from the worklight when
it is fully charged.
3.2 OPERATION
Caution
! Never shine the LED light directly into your or
any one else’s eyes.
3.2.1 Press the on/off switch ,run through the sequence
of modes (3 Watt COB,1W LED on top and off)
3.2.2 The worklight can be suspended and swivel 360
degree on hooks or the magnets located on the rear
and located on the base of the worklight.
3.2.3 The worklight can be swiveled 180° to achieve the
desired angle.
4. MAINTENANCE
Keep the worklight clean from dirt and grease, using a
damp cloth. Do not submerge in water.
Specifications
Art no.
700327
Total output:
3 W/1 W
Luminous flux
300 lm/100 lm
Charging time:
~4 hour
Burning time:
~8 hours (flashlight)/ ~3 hours (working light)
Protection class:
IP20
Input voltage:
5V DC max 1A
Warm up time:
<1 s
Switch cycles:
15.000x
LED lifetime:
30.000 hours
Colour temperature:
6.500 K (Cool White)
Colour Rendering Index:
Ra > 70
Beam angle:
90°/15°
700327-MAN-ML-2017100201-SHA.indd 3
2017-10-02 14:40:57
