background image

 

 

5

 

General Guidelines

 

This device is a lighting effect for professional use on stages, in discotheques, theaters, etc., the device was 

designed for indoor use only. 

This fixture is only allowed to be operated with the max alternating current which stated in the technical 

specifications in the last page of this manual. 

The device can do 

  continuous 

  work for eight hours.    Lighting effects are not designed for permanent 

operation. Consistent operation breaks may ensure that the device will serve you for a long time without 
defects. 

Handle with care, do not make the device by strong shocks. 

While choosing the installation-spot, please make sure that the device is not exposed to extreme heat, moisture 
or dust. Please don't project the beam onto combustible substances.The minimum distance between light-output 
from the projector and the illuminated surface must be more than 1 meter.   

►Please do not in damp, overheat or dusty environment install and use the device. Do not use light on fuel. The 
distance between the device and the projectile to keep at least 1 meter. 

►If you use the quick lock cam in hanging up the fixture, please make sure the quick lock fasteners turned in 
the quick lock holes correctly.   

►Operate the device only after having familiarized with its functions. Do not permit operation by persons not 
qualified for operating the device. Most damages are the result of unprofessional operation.   

►Please use the original packaging if the device is to be transported.   

►For safety reasons, please be aware that all modifications on the device are forbidden.   

►If  this  device  will  be  operated  in  any  way  different  to  the  one  described  in  this  manual,  the  product  may 
suffer  damages  and  the  guarantee  becomes  void.  Furthermore,  any  other  operation  may  lead  to  short-circuit, 
burns, electric shock, lamp explosion, crash, etc. 

 

3.

 

Installation 

  Instruction

 

 
 
 

 

►The applicable temperature for the lighting is between -25°C to 45°C. Do not use the lighting under or above 
the temperature. 

►The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for 
1 hour without any harming deformation.   

 

                                                                           

  CAUTION!

 

                         

Please consider the GB7000.15/EN60598-2-17 and the other respective national norms during 

                          The installation. The installation must only be carried out by a qualified person. 

 

Summary of Contents for MSL-3W RGB












Reviews: