background image

www.prolight.co.uk

Event Spot Rapid RGBW

  

User Manual

12

Operating instructions

Optional IR remote functions:

 

Button functions:

DMX address examples:

Important notes:

• 

Set the DMX address on each fixture before plugging into the DMX controller

• 

The IR remote cannot be used when the fixture(s) are being controlled with a DMX controller

• 

The maximum IR transmitter distance is 10m - Please make sure that you have the IR remote  
aimed directly at the front panel of each fixture to be programmed

• 

If you do not press the “DMX MODE” button after you have changed the DMX address when you  
power down the fixture it will lose the address you have set

01 - Sets the LEDs into power on or off modes
02 - Runs the built-in programs, use the ‘+’ and ‘-’  

    buttons to go through the programs

03 - Sets the LEDs to flash on and off, use the ‘+’  

    and ‘-’ buttons to change the flash frequency

04 - Sets the run speed, use the ‘+’ and ‘-’ buttons  

    to change the desired speed (note: only available in  
    the colour change or colour fade modes)

05 - Sets the LEDs into DMX mode
06 - Sets the LEDs into sound active mode
07 - Sets the LEDs into slave mode
08 - Sets the DMX address for the LEDs
09 - Sets the LEDs colour, then use the ‘+’ and ‘-’ 

    buttons to change the brightness

1 2 3
4 5 6 0

+

_

7 8 9

AW

D

FL

SL

SP

S

S PR

SA

R

G

B

BLACKOUT

DIMMING

FLASH

SLAVE

SPEED

SET ADDR

SELECT PROG

SOUND ACTIVE

AMBER/WHITE

DMX MODE

02

01

03

09

09

04

06

07

05

08

To set the DMX address “245”;

• 

Press the “S” button, the red LEDs will come on, 
you can now start to set the DMX address

• 

Now press the “2” button, the green LEDs will 
come on, this means the first digit has been  
set at 2

• 

 Now press the “4” button, the blue LEDs will 
come on, this means the second digit has been 
set at 4

• 

 Now press the “5” button, and the white/amber  
LEDs will come on, the third digit 5 has been set. 
The full DMX address setting has been changed

• 

Now press the “DMX MODE” button to save  
the new address into the memory

To set the DMX address “002”;

• 

Press the “S” button, the red LEDs will come on, 
you can now start to set the DMX address

• 

Now press the “0” button, the green LEDs will 
come on, this means the first digit has been  
set at 0

• 

 Now press the “0” button, the blue LEDs will 
come on, this means the second digit has been 
set at 0

• 

Now press the “2” button, and the white/amber  
LEDs will come on, the third digit 5 has been set. 
The full DMX address setting has been changed

• 

 Now press the “DMX MODE” button to save  
the new address into memory

Optional 

IR remote 

Order code: 

LEDJ90C

Summary of Contents for Event Spot Rapid RGBW Series

















Reviews: