background image

| 11

LEANLED II

www.led2work.com

  6  |  Maintenance and Care

The LED luminaire is maintenance-free. Do not make any alterations to the luminaire 

(except according to the mounting information contained in this manual).
The luminants used in the luminaire have a very long life and cannot be replaced.
Turn off the light before cleaning and let it cool down completely. Clean the outside of 

the luminaire with a soft, dry and clean cloth. To remove excess dirt, moisten the cloth 

with water. Never use aggressive cleaning agents, as these may cause discolouration 

of the housing.

No liability is assumed for damages resulting from the use of unsuit-

able cleaning agents.

  7  |  Warranty

We supply a full warranty for the product for 36 months from the date of purchase. This 

warranty applies for fault-free working under proper use and in accordance with the 

operating instructions.
During the warranty period defects and faults in the product will be rectified free of 

charge if they are proven to be caused by material, processing or design errors. If the 

purchaser complains of a material defect, he bears the burden of proof to demonstrate 

that the product was already defective upon receipt.

The warranty does not extend to defects caused by wear, negligen-

ce or improper use.
Further claims, in particular claims for compensation for damage 

that did not occur on the LED luminaire itself, are excluded.

  8  |  Disposal

The luminaire must be disposed of at a suitable disposal 

site designated for recycling of electrical and electronic 

equipment in accordance with local, national regula-

tions. (WEEE-Nr. 32828318)

  9  |  Customer service

If you have any problems or questions concerning this product, please contact us!
By phone:   +49 7231 44920-00 

 

Monday to Thursday   8:00 am to 12:00 midday and 1:00 pm to 4:30 pm 

 

Friday 

 

8:00 am to 12:00 midday and 1:00 pm to 3:00 pm

By email:   [email protected]

Summary of Contents for 111010-01













Reviews: