background image

 

                                                                                                                                                     

User

s Manual   

For

 

 

ME542 

Economical Microstepping Driver

 

Version

 

1.0 

©

2006 All Rights Reserved

 

 

Attention: Please read this manual carefully before using the driver!

 

 

3/F, Block 2, Nanyou Tianan Industrial Park, Nanshan Dist, Shenzhen, China 

PH. (86)755-26434369            FAX (86)755-26402718 

Web site: 

www.leadshine.com

    E-Mail: 

[email protected]

 

 

 

The

 

content  in  this  manual  has  been  carefully  prepared  and  is  believed  to  be  accurate,  but  no 

responsibility is assumed for inaccuracies. 
 
Leadshine  reserves  the  right  to  make  changes  without  further  notice  to  any  products  herein  to 
improve reliability, function or design. Leadshine does not assume any liability arising out of the 
application or  use of  any  product  or  circuit described herein;  neither  does  it  convey  any  license 
under its patent rights of others.   
 
Leadshine

s general policy does not recommend the use of its products in life support or aircraft 

applications wherein a  failure or malfunction of the product may directly threaten life or injury. 
According to Leadshine

s terms  and conditions of sales, the user of Leadshine

s products in life 

support or aircraft applications assumes all risks of such use and indemnifies Leadshine against all 
damages. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

©

2006 by Leadshine Technology Company Limited. 

All Rights Reserved

Authorized Distributor of Leadshine Technology

www.leadtronker.com

www.leadtronker.com

雷赛智能官方代理:雷创智能科技

Summary of Contents for ME542










Reviews: