background image

                                 

MA860H Microstepping Driver Manual V1.0

 

Tel: +086 0755-26434369                                  13                                  Web Site: www.leadshine.com 

Problem Symptoms and Possible Causes 

Symptoms 

Possible Problems 

No power 

Microstep resolution setting is wrong 

DIP switch current setting is wrong   

Fault condition exists 

Motor is not rotating 

The driver is disabled 

Motor rotates in the wrong direction   

Motor phases may be connected in reverse 

DIP switch current setting is wrong 

The driver in fault 

Something wrong with motor coil 

Control signal is too weak 

Control signal is interfered 

Wrong motor connection 

Something wrong with motor coil 

Erratic motor motion 

Current setting is too small, losing steps 

Current setting is too small 

Motor is undersized for the application   

Acceleration is set too high 

Motor stalls during acceleration 

Power supply voltage too low 

Inadequate heat sinking / cooling 

Automatic current reduction function not being utilized 

Excessive motor and driver heating 

Current is set too high 

 

                               

MA860H Microstepping Driver Manual V1.0

 

Tel: +086 0755-26434369                                  13                                Web Site: www.leadshine.com 

APPENDIX 

Twelve month limited warranty   

Leadshine  Technology  Co.,  Ltd.  warrants  its  products  against  defects  in  materials  and 
workmanship for a period of 12 months from shipment

 

out of factory. During the warranty period, 

Leadshine will either, at its option, repair or replace products which proved to be defective. 

Exclusions                                                                                                                           

The above warranty does not extend to any product damaged by reasons of improper or inadequate 
handlings  by  customer,  improper  or  inadequate  customer  wirings,  unauthorized  modification  or 
misuse,  or  operation  beyond  the  electrical  specifications  of  the  product  and/or  operation  beyond 
environmental specifications for the product. 

Obtaining warranty service                                                                                     

To  obtain  warranty  service,  a  returned  material  authorization  number  (RMA)  must  be  obtained 
from  customer  service  at  e-mail: 

[email protected]

  before  returning  product  for  service. 

Customer  shall  prepay  shipping  charges  for  products  returned to  Leadshine  for  warranty  service, 
and Leadshine shall pay for return of products to customer.   

Warranty limitations                                                                             

Leadshine  makes  no  other  warranty,  either  expressed  or  implied,  with  respect  to  the  product. 
Leadshine  specifically  disclaims  the  implied  warranties  of  merchantability  and  fitness  for  a 
particular purpose. Some jurisdictions do not allow limitations on how long and implied warranty 
lasts, so the above limitation or exclusion may not apply to you. However, any implied warranty of 
merchantability or fitness is limited to the 12-month duration of this written warranty. 

Shipping failed product                                                                                                     

If your product fail during the warranty period, e-mail customer service at 

[email protected]

 to 

obtain  a  returned  material  authorization  number  (RMA)  before  returning  product  for  service. 

Please  include  a  written  description  of  the  problem  along  with  contact  name  and  address.  Send 

failed product to distributor in your area or: Leadshine Technology Co., Ltd. 3/F, Block 2, Nanyou 

Tianan  Industrial  Park,  Nanshan  Dist,  Shenzhen,  China.  Also  enclose  information  regarding  the 

circumstances prior to product failure.

 

Summary of Contents for MA860H










Reviews: