background image

 

 

User

s Manual   

For 

DM856 

Fully Digital Stepping Driver

 

Version 1.0 

©

2009 All Rights Reserved

 

Attention: Please read this manual carefully before using the driver! 

 

 

3/F, Block 2, Nanyou Tianan Industrial Park, Nanshan Dist, Shenzhen, China 

T: (86)755-26434369            F: (86)755-26402718 

Web site: 

www.leadshine.com

      E-Mail

[email protected]

 

 

 

The

 

content  in  this  manual  has  been  carefully  prepared  and  is  believed  to  be  accurate,  but  no 

responsibility is assumed for inaccuracies. 

Leadshine  reserves  the  right  to  make  changes  without  further  notice  to  any  products  herein  to 

improve reliability, function or design. Leadshine does not assume any liability arising out of the 

application  or  use  of  any  product  or  circuit  described  herein;  neither  does  it  convey  any  license 

under its patent rights of others.   

Leadshine

s  general policy does  not recommend  the  use of  its products in life  support  or aircraft 

applications  wherein  a  failure  or  malfunction  of  the  product  may  directly  threaten  life  or  injury. 

According  to  Leadshine

s  terms  and  conditions  of  sales,  the  user  of  Leadshine

s  products  in  life 

support or aircraft applications assumes all risks of such use and indemnifies Leadshine against all 

damages. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

©

2009 by Leadshine Technology Company Limited. 

All Rights Reserved

 

Summary of Contents for DM856


















Reviews: