background image

1 About this Manual

Read this manual carefully and keep it in a safe place. This manual is aimed at

Skilled workers in the field of automotive electrics.
Any modifications to the product or its components are prohibited and do not
conform to its intended use. Only use original LEAB or LEAB-approved ac-

cessories.
Throughout the manual, you will be alerted to warnings and safety notices
about potential hazards associated with handling the device. The colours and

signal words indicate the severity of the hazard:

Notice

Possibility of material damage
The signal word 

Attention 

indicates that there is a possibility of

material damage. To avoid material damage, follow the

instruction.

 CAUTION

Danger that can lead to minor injuries
Safety instructions with the signal word 

CAUTION 

indicate a

hazard which, if not avoided, can result in minor or moderate
injury. Read the safety instructions carefully and follow them to

avoid the hazard.

 WARNING

Hazards that can lead to severe injuries or death
Safety instructions with the signal word 

WARNING 

indicate a

hazard which, if not avoided, can result in death or severe injury.
Read the safety instructions carefully and follow them to avoid

the hazard.

3

LEAB Automotive GmbH

Thorshammer 6

24866 Busdorf

LEAB Automotive GmbH

1 About this Manual

Summary of Contents for 0101033351





















Reviews: