background image

 

 

PAGE 21

 

A WORD ABOUT TUNING ETIQUETTE 

Be  sure  to  use  a  vacant  frequency  when  tuning.  With  today’s  crowded  ham  bands,  this  is 

often  difficult.  However,  causing  interference  to  other  hams  should  be  avoided  as  much  as 
possible. The AT-897Plus’s very short tuning cycle, as little as a fraction of a second, minimizes 
the impact of tuning transmissions. 

CARE AND MAINTENANCE 

The AT-897Plus tuner is essentially maintenance- free. Power limits in this manual should be 

strictly  adhered  to.  Be  sure  also  to  observe  the  proper  precautions  when  tuning  on  the  6  meter 
band. 

The outer case may be cleaned as needed with a soft cloth slightly dampened with household 

cleaning  solution.  As  with  any  modern  electronic  device,  the  AT-897P lus  can  be  damaged  by 
temperature extremes, water, impact, or static discharge. LDG strongly recommends the use of a 
good quality, properly installed lightning arrestor in the antenna lead. 

TECHNICAL SUPPORT 

The  LDG  website  provides  links  to  product  manuals,  just  in  case  you  lose  this  one!  When 

you  are  thinking  about  the  purchase  of  other  LDG  products  our  website  also  has  complete 
product specifications and photographs you can use to help make your purchase decision.  Don’t 
forget  the  links  to  all  of  the  quality  LDG  Dealers  also  ready  to  help  you  make  that  purchase 
decision. 

TWO-YEAR  TRANSFERRABLE WARRANTY 

Your product  is  warranted against  manufacturer defects  in parts and  labor  for  two  full  years 

from  the  date  of  purchase.  This  two-year  warranty  is  also  transferable.  When  you  sell  or  give 
away your LDG product give the new owner a copy of the original sales receipt and the two- year 
warranty goes with the new owner. 

There  is  no  need to complete a  warranty card or to  register an  LDG product.  Your product 

receipt establishes eligibility for warranty service so save that receipt. Send your receipt with the 
product  whenever  you  send  your  product  to  LDG  for  repair.  Products  sent  to  LDG  without  a 
receipt are considered requests for out-of-warranty repair. 

LDG does  not  warranty against product damage or abuse.  This  means that a product  failure, 

as determined by LDG, to be caused by the customer or by other natural calamity (e.g. lightning) 
is  not  covered  under  the  two-year  warranty.  Damage  can  be  caused  by  failure  to  heed  the 
product’s published limitations and specifications or by not following good Amateur practice.  

OUT OF WARRANTY SERVICE 

Any  time  a  product  fails  after  the  warranty,  LDG  wants  to  help  you  get  it  fixed.  Send  the 

product  to  us  for  repair.  We  will  determine  what  needs  to  be  done,  and  based  on  your  prior 
instruction; either contact you with an estimate or fix it and contact you with a request to pay any 
repair  charges.  Please  contact  LDG  if  you  have  any  questions  before  you  send  us  an  out-of-
warranty product for repair.  

Summary of Contents for AT-897Plus























Reviews: