background image

 3  FRONT PANEL

1.

PROT/STBY: 

This indicator shows two different statuses:

PROT:  protection indicator. The indicator will light up orange when the amplifier is in 
protection condition.  Protection may be because of a short-circuit in the speaker line, 
the amplifier overload and when the inside temperature is over 55ºC (131 ºF). There's 
and independent protection indicator for each channel. 

STBY: stand-by. The same indicator will light up orange when the amplifier is in stand-
by due to not detecting any sinal for more than two minutes.The indicator will switch off 
when the system detects the signal again. This function is programmable through the 
switch located on the rear panel. 

2.

CLIP:

  The clip indicator will light red when the input or output is too high. There ir an 

independent CLIP indicator for each channel 

3.

INPUT:

  The input indicator will light green when an input signal is detected. There is an 

independent input indicator for each channel. 

4.

OUTPUT:

 The output indicator will light green when there is an output signal. El indicador 

de   salida   se   iluminará   en   verde   hay   señal   de   salida.  There   is   an   independent   output 
indicator for each channel. 

5.

POWER:

 The power indicator will light blue when the equipment is on. 

6.

POWER SWITCH:

 It allows to switch the equipment on and off. 

LDA Audio Tech - Severo Ochoa Nº 31- 29590 MÁLAGA, ESPAÑA. Tlf: +34 952028805

3

User's manual: BA Series

Figure 1: BA Series Front View

Summary of Contents for BA-2250

















Reviews: