background image

Model 8310-2210

Installation Instructions

Description

Actuator

Available faceplates:
Single gang: 2-3/4” x 4-1/2” stainless steel, fits on single gang electrical boxes.

Receiver

•  3 Modes of Operation:

•  Delayed  (1 - 15 Seconds)

•  No Delay  (1 – 30 Seconds)

•  Latching

•  Adjustable Range:  3’ - 300’

•  40 Transmitter capacity: delayed, non-delayed or both 

•  Form ‘C’ Relay Output

•  12/24V AC/DC operation

•  915 MHz

•  Dimensions:  2-5/8” x 1-1/2” x 

13/16”

Technical specifications

Actuators

Descriptions

8310-2210 Series

Number of IR sensors

1

Batteries (supplied)

“AA” alkaline batteries

Estimated battery life

2 years (based on 100 operations/day)

Standard operating range

1” - 12” (25.4mm - 304mm) 

Factory set to 6” (152mm)

Operating mode

Momentary

Inputs

“Request to Exit” (to trigger the relay remotely or from the other side of the door)

Wireless output

Built-in 915 Mhz. spread spectrum wireless transmitter

Receivers

Descriptions

8310-2210 Series

Operating voltage

12/24V AC/DC

Current Draw

23 mA nominal @ 24V AC/DC
43 mA maximum @ 24V AC/DC

Response time

30 - 200 ms

Memory delay & No delay

40 transmitters total

LEDs

Indicate: relay status; learn mode; erase mode; and potentiometer position

Output

1 x SPDT relay contact

Rating

3 amps @ 30 VDC

Operating time

1 - 30 seconds

Delay time

1 - 15 seconds

Frequency

915 Mhz

Mounting

2 #4 screws at 3” centers or hook and loop fastener (supplied)

Enclosure

Clear plastic case

Dimension

2-5/8” x 1-1/2” x 13/16”

8310-2210 Series Touchless Actuator/

Transmitter Battery Powered Contactless Switch

Summary of Contents for 8310-2210 Series








Reviews: