11
10
– To reduce the risk of injury:
• Do not operate the unit until the back is installed and locked.
• The back of the unit must be lifted for assembly. Please seek assistance if you are
unable to lift at least 45 pounds without strain.
WARNING
NOTICE:
-- To reduce the risk of product damage:
• Do not plug in until instructed.
1. Once the furniture is unpacked, carefully remove the red electrical components bag from the body
bracket and set aside; depending on the product purchased, inside the bag are the power supply,
power cord, optional remotes and three AAA batteries for the optional remote (F
IGURE
1).
2. Make back electrical connections.
•
Lay the back across the arms of the chair. Turn the locking levers, located on the brackets
attached to the back (one on each side), to a 90° angle (F
IGURES
2
AND
3).
•
Locate and identify the electrical connection between the back and the body. The color of the
connectors varies by date of manufacture.
-
The brown connectors on the right side (sitting) are for the adjustable headrest feature. One
connector routes from bottom of the back panel and the other between the rear seat and tailgate.
- The orange connectors on the left side (sitting) are for the adjustable lumbar feature. One connector
routes from bottom of the back panel and the other between the rear seat and tailgate.
•
Carefully rotate the back until the headrest and lumbar actuator cables are able to reach the connectors.
•
Connect the adjustable headrest (F
IGURE
4). Align the pins and sockets in the brown connectors,
push the connectors together and close the locking cover to secure the connection.
•
Connect the adjustable lumbar (F
IGURE
4). Align the pins and sockets in the orange connectors,
push the connectors together and close the locking cover to secure the connection.
Power Recliner with Headrest
and Lumbar Assembly Instructions
3. Install the back.
•
Continue rotating the back at a slight angle, making sure the headrest and lumbar connections fall
between the rear seat and tailgate, and align the brackets on the back with the brackets on the
body (F
IGURE
2).
•
Lower the back onto the body, making sure the back and body brackets are completely engaged.
-
To make sure the back is properly installed with both sets of back and body brackets
engaged, stand behind the chair and twist the back from side to side. If one or both sides
move out of position the brackets are not engaged (F
IGURE
5). Remove the back and repeat
the steps above.
-
If you are unable to install the back properly, contact your La-Z-Boy
®
dealer for assistance.
•
Lock the brackets by using a screwdriver to push down the locking levers (F
IGURE
3).
4. Remove the power supply from its packaging from the electrical components bag. Remove the power
supply and 120 volt power cord from the package.
5. Locate the motor connector behind the unit. Connect the motor connector to the power supply
connector. Align the connectors, push together until fully seated and close the locking cover to
secure the connection (F
IGURE
6).
6. Connect the 120 volt power cord to the power supply (F
IGURE
6). Do not plug in until instructed in
the operating instructions.
7. Proceed to the
Battery Backup Assembly Instructions
.
8. To remove the back, unplug the 120 volt power cord from the electrical outlet and disconnect the
power supply from the motor connector behind the unit. Reverse the
Assembly Instructions
steps.
When lifting the back up from the body, to lay across the arms,
make sure
to do so slowly and carefully
to prevent damage to the electrical connections.
Body
Bracket
F
IGURE
1
F
IGURE
2
F
IGURE
4
F
IGURE
5
Electrical
Components Bag
Back and body brackets on this
side are not engaged. Remove
the back and reinstall.
Adjustable Headrest
Connection Brown
Tailgate
Rear Seat
Back
Bracket
Locking
Lever
at a 90
Degree
Angle
Locked
Position
Power Recliner with Headrest
and Lumbar Assembly Instructions
Back Bracket
Body
Bracket
Adjustable Lumbar
Connection Orange
F
IGURE
6
120 Volt Power Cord
Make this
connection
Power Supply*
Motor Connector
Make this
connection
*
Power supplies/connections
may vary by date of manufacture.
F
IGURE
3
