LAWO V_pro8 Installation & Operation Manual Download Page 86

Page: 86 / 109

V1.0/2

V_pro8 Manual

Operation (Web Browser Control)

MADI Out

This main menu displays audio metering and provides access to signal routing and output delay for
all MADI output channels.

You can configure redundant MADI ports by making

connections

from both the front and

rear panel.

Select

MADI Out

and a set of channels (

MADI 1

1-32, MADI 1 33-64

, etc. ) from the main

menus.

In the upper part of the operating window you will see audio metering for the 32 output channels:

The meter scale is dBFS, and includes a peak hold indicator (green) and overload flag (red) if audio
levels reach 0dBFS. The peak hold indicator clears automatically after a few seconds.

The lower half of the screen can be used to adjust signal routing or delay, see

Signal Routing

and

Delay

Summary of Contents for V_pro8














































































































Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands

LAWO V_pro8, Installation & Operation Manual

Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands