LAWO V_pro8 Installation & Operation Manual Download Page 35 | Manualshive

Page: 35 / 109

background image

V_pro8 Manual

V1.0/2

35

Installation & Configuration
Signal Connections

MADI Connections

Front Panel

Rear Panel

The

pro8

provides two MADI in/out ports (

MADI

1

&

2

) available for connection from the front and/or

rear panel.

Each port carries up to 64 input and output channels and conforms to AES10.

Connections are available on optical fibre LC connectors, once you have fitted the recommended

The front and rear ports operate in parallel. This allows you to configure main and redundant MADI
links. Both front and rear MADI outputs are always active. For the return link, in Version 1.0, the first
recognised and locked input is used. (In a future software release, you will be able to select the active
MADI input (front or rear) from the user interface.)

An LED for each port indicates the status:

Green

= MADI link is active.

Flashing Red

= MADI link is asynchronous.

Off

= no connection or MADI link is invalid.

«
...
33
34
35
36
37
...
»

Summary of Contents for V_pro8














































































































Reviews:

No comments

Related manuals for V_pro8

Brand: XINDAK Pages: 8

Brand: La Marche Pages: 15

Brand: Barco Pages: 4

Brand: Vanner Pages: 44

Brand: OCULUS Pages: 28

Brand: GME Pages: 21

Brand: Helvest Pages: 2

Brand: OTS Pages: 14

EQUINOX EQX2 4002-HT

Brand: Salicru Pages: 108

10/100/1000 (SFP)

Brand: Dynamix Pages: 2

Brand: Viking Pages: 6

MOB31-12HFN1-QRD0GW

Brand: Midea Pages: 65

Brand: GoMax Electronics Pages: 12

Compressor Drive CD302

Brand: Danfoss Pages: 28

IRIS BLUE 3 SQ727 Series

Brand: SALUPO Pages: 28

Brand: Cobra Pages: 12

Brand: SMA Pages: 272

Brand: SolaX Power Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands