LAWO V_pro8 Installation & Operation Manual Download Page 20

Page: 20 / 109

V1.0/2

V_pro8 Manual

Installation & Configuration

Adaptor Installation

MADI Port Adaptors

Rear MADI Ports (no adaptors fitted)

Front MADI Ports (with Optical LC Duplex Connectors)

The

pro8

is shipped with two SFP transceivers so that you may connect optical fibre to the MADI

ports.

Either of the following transceivers are recommended:

Skylane SFP Transceiver (Part Number SFP13002EG0D000)

Avago LC Duplex Connector Optical Interface (Part Number HFBR-57E0PZ).

Note that you will require an adaptor for each MADI connection - that's four adaptors in total, if you
wish to connect MADI ports 1 & 2 at both the front and rear of the unit.

The SFP transceivers are hot-pluggable. To install, push each adaptor into the rectangular

MADI

slot.

Press gently and firmly until the adaptor locks into position.

Summary of Contents for V_pro8














































































































Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands

LAWO V_pro8, Installation & Operation Manual

Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands