LawnMaster CLPS4008 Operator'S Manual Download Page 31 | Manualshive

Page: 31 / 37

LawnMaster CLPS4008 Operator'S Manual Download Page 31

31

CARE AND MAINTENANCE

Maintenance

Before and after each use, check the product including accessories and attachments for loose
fasteners, leaks and worn or damaged parts. If required, exchange them for new ones as described
in this instruction manual. Observe the technical requirements.

Battery Pack And Charger (Not Included)

NOTE: Please consult the instructions for use supplied with battery pack and charger for more details.

Storage

● Switch the product off and remove the battery pack.
● Clean and maintain the product before storage as described above.
● Attach the scabbard (15).
● Store the product and its accessories in a dry, frost-free place.
● Always store the product in a place that is inaccessible to children. The ideal storage temperature

is between 10°C and 30°C.

● We recommend using the original package for storage or covering the product with a suitable

cloth or enclosure to protect it against dust.

Transportation

● Switch the product off and remove the battery pack.
● Attach transportation guards, if applicable.
● Always carry the product on its handles (2, 9).
● Protect the product from any heavy impact or strong vibrations which may occur during

transportation in vehicles.

● Secure the product during transport to prevent loss of lubricant, damage or injury.

«
...
29
30
31
32
33
...
»

Summary of Contents for CLPS4008






































Reviews:

No comments