background image

14

3352-942 Rev B

4.

Push the cable jacket upward 1/8 inch (3 mm).

Note:

 You can place a ruler against the upper side

of the black cable mount (C) and measure how far

the upper end of the cable jacket (D) moves.

C

D

Note:

 Moving the cable jacket upward decreases

the ground speed; moving the jacket downward

increases the ground speed.

5.

Tighten the nut firmly.

6.

Start the mower and check the adjustment.

Note:

 If the self-propel is not properly adjusted,

repeat this procedure.

Replacing the Blade

Important

You will need a torque wrench to

install the blade properly.

 If you do not have a

torque wrench or are uncomfortable performing this

procedure, contact an Authorized Service Dealer.
Examine the blade whenever you run out of gasoline.

If the blade is damaged or cracked, replace it

immediately. If the blade edge is dull or nicked, have

it sharpened or replace it.

Warning

The blade is sharp; contacting the blade can

result in serious personal injury.
Wear cloth or leather gloves when servicing the

blade.
1.

Disconnect the spark plug wire from the spark

plug. Refer to Preparing for Maintenance on page 12.

2.

Tip the mower onto its side (with the air filter up).

3.

Use a block of wood to hold the blade steady.

4.

Remove the blade, saving all mounting hardware.

5.

Install the new blade and all mounting hardware.

Important

: Position the curved ends of the blade to

point toward the mower housing.

m-6216

6. Use a torque wrench

 to tighten the blade bolt to

60 ft-lb (82 N

m).

Important

A bolt torqued to 60 ft-lb (82 N

V

m) is

very 

tight. While holding the blade with a block of

wood, put your weight behind the ratchet or

wrench and tighten the bolt securely. This bolt is

very difficult to overtighten.

Cleaning the Mower

1.

With the engine

running on a flat paved

surface, spray a stream

of water in front of the

right rear

 wheel.

1093

The water will splash into the path of the blade,

cleaning out the clippings.

2.

When no more clippings come out, stop the water

and move the mower to a dry area.

3.

Run the engine for a few minutes to dry the

housing to prevent it from rusting.

Summary of Contents for Insight 10685

















Reviews: