![background image](http://html1.mh-extra.com/html/lavor/mchpv/mchpv_manual_4056955021.webp)
21
EN
socket must be watertight and the cable
must have the dimensions shown in the
table below.
(if fi tted)
PLEASE NOTE:
This water cleaner is equipped
with the A.S.S. (Automatic Stop System), which
stops the machine during the bypass phase. To
start the water cleaner, it is therefore necessary
to set the switch on position “ON”; after that
press the pistol trigger: the Automatic Stop
System will start the machine and will stop it
automatically when the trigger is released. It is
advisable to put on the safety of the pistol trig-
ger whenever the machine is stopped, in order
to avoid unintentional starting.
• Any automatic start of the machine with-
out pressing the gun trigger is attributable
to air bubbles in the water or other similar
phenomena which do not imply the exist-
ence of any defects in the machine.
• Do not leave the appliance unattended
during the standby for more than 5 minutes.
Contrarily, for the safety of the appliance it
is necessary to re-turn the switch into the
OFF position.
• Please check that the coupling of the high
pressure hose with the appliance and the gun
supplied as standard equipments made cor-
rectly, that is to say without any water leak.
If the appliance is equipped with a pressure
regulator:
• when the pressure is set to minimum the
A.S.S. may not trigger. Therefore, do not al-
low the appliance to function in by-pass for
more than 1 minute.
• do not act on the gun lever too frequently
(this may cause a malfunction).
> SUITABLE USE OF THE MACHINE
The performances of the machine are suitable
for a professional use. Structural technologies
have been studied to assure high reliability
and safety levels, and long life. It is absolutely
forbidden to use the machine in potentially
explosive environments or areas. The work-
ing temperature must range b5° and
+50°C. It is forbidden to carry out any modifi ca-
tion to the structure and to any elements of the
machine.
CORRECT USE OF THE MACHINE
• The cleaner must be placed on a fi rm, stable
surface and must be horizontal.
• In case of operation indoors, adequate venti-
lation and gas venting must be assured.
• Whenever using the high-pressure cleaner,
users are urged to hold the gun in the correct
position, with one hand on the grip and the
other on the spray rod.
• The water jet must never be pointed at the
electrical cables or at the machine.
> UNPACKING
After opening the package, check the entire
unit.
• In case of problems with this unit do not use it
until you have consulted an authorized serv-
ice/centre.
• Due to transport and packing dimension rea-
sons, some accessories can be supplied dis-
assembled; in this case the fi tting has to be
carried out following the instructions on this
booklet.
• All possible harmful parts of the package
(plastic bags, foamed polystyrene, nails etc.)
should be kept out of children’s reach.on
ground and take the pallet off .
> INSTALLATION AND START-UP
WARNING: The installation of the unit
230-240V
400-415V
3G 2,5 mm
2
4G 2,5 mm
2
max 20 m
max 30 m
Summary of Contents for MCHPV
