background image

LAUNCH                                                       X-431 Russia GAZ Diagnosis

 

Introduction 

 

X-431 is the most advanced automobile 
diagnostic unit in the world at present. Please 
refer to X-431 User’s Manual  for its features, 
hardware configuration, printer operation, 
button description, conditions for test, etc. 
 
Here we describe the operation procedure for 
Russia GAZ diagnostic program. 

Select Diagnostic Connector 

At present, this diagnostic program can be used 
to diagnose GAZ vehicle up to 2003 with 12PIN 
diagnostic socket.  So,  select  [GAZ-12PIN] 
diagnostic connector when doing test. 

Diagnostic Socket Location 

The  GAZ 12PIN diagnostic socket is usually 
located in the engine compartm ent. 

Pin Definitions 

GAZ 12PIN Diagnostic Socket 

The GAZ 12PIN diagnostic socket is as shown in 
Figure 01.   

12  11  10 

Figure 01 

 

PIN definition of GAZ 12PIN diagnostic socket 

PIN

 

Definition

 

Power (+) 

11 

Ground (-) 

12 

K line 

 

Connection 

Refer to Figure 02  for connection before 
performing diagnosis. 

 

To vehicle 
diagnostic 
socket

Figure 02 

 

??

Insert the CF car d into the  CF card  slot, 

(Note:  keep the face labeled  “UPSIDE” 

upward),

 and make sure the card is fully 

seated. 

??

Insert one end of the main cable into the 
diagnostic socket on SMARTBOX. 

??

Connect the other end of the main cable to 
the [GAZ-12PIN] diagnostic connector. 

??

Connect the other end of  the diagnostic 
connector to GAZ 12PIN diagnostic socket. 

 

Note:  If the power supply on vehicle 

diagnostic socket is insufficient or 

the power pin is damaged, you can 

get power in the following ways: 

 

? ?

From cigarette lighter: insert one end of 

the cigarette lighter cable into the lighter 

socket in vehicle and connect the other 

end to the power connector of X-431 

main cable. 

? ?

From battery: clamp the  two clips of 

battery cable on the positive  and 

negative  poles of battery and insert 

another end of the cable into the power 
connector of X-431 main cable. 

? ?

From  power adapter: connect the power 

adapter  to  the  100-240V AC outlet with 

power cord.  Insert the 12V DC plug of 

power adapter into the power connector 

of X-431 main cable. 

Summary of Contents for X-431 PADII













Reviews: