background image

LAUNCH                                                       X-431 Russia GAZ Diagnosis

 

Trademark Information 

 

LAUNCH

 is a registered trademark of 

LAUNCH TECH  CO., LTD. (also called 
LAUNCH for short) in China and other countries. 
All other LAUNCH trademarks, service marks, 
domain names, logos, and company names 
referred to in this manual are either trademarks, 
registered trademarks, service marks, domain 
names, logos, company names of or are 
otherwise the property of LAUNCH or its 
affiliates. In countries where any of the 
LAUNCH trademarks, service marks, domain 
names, logos and company names are not 
registered, LAUNCH claims other rights 
associated with unregistered trademarks, 
service marks, domain names, logos, and 
company names. Other products or company 
names referred to in this manual may be 
trademarks of their respective owners. You may  
not use any trademark, service mark, domain 
name, logo, or company name of LAUNCH or 
any third party without permission from the 
owner of the applicable trademark, service 
mark, domain name, logo, or company name. 
You may contact LAUNCH by visiting Launch at 
www.cnlaunch.com, or writing to  LAUNCH, 
Xinyang Building, Bagua 4th Road, Shenzhen, 
Guangdong Province, P. R. C., to request 
written permission to use Materials on this 
manual for purposes or for all other questions 
relating to this manual. 

Copyright Information 

 

Copyright ©   2000 by LAUNCH TECH. CO., LTD. 
All rights reserved. No part of this publication 
may be reproduced, stored in a retrieval system, 
or transmitted in any form or by any means, 
electronic, mechanical, photocopying, recording 
or otherwise, without the prior written 
permission of LAUNCH. The information 
contained herein is designed only for the use of 
this unit. LAUNCH is not responsible for any 
use of this information as applied to other units.   
Neither LAUNCH nor its affiliates shall be liable 
to the purchaser of this unit or third parties for 

damages, losses, costs, or expenses incurred 
by purchaser or third parties as a result of: 
accident, misuse, or abuse of this unit, or 
unauthorized modifications, repairs, or 
alterations to this unit, or failure to strictly 
comply with LAUNCH operating and 
maintenance instructions.   
 
LAUNCH shall not be liable for any damages or 
problems arising from the use of any options or 
any consumable products other than those 
designated as Original LAUNCH Products or 
LAUNCH Approved Products by LAUNCH.   
 

General Notice 

 

??

Other product names used herein are for 
identification purposes only and may be 
trademarks of their respective owners. 
LAUNCH disclaims any and all rights in 
those marks.   

??

There is a possibility that this unit is 
inapplicable to some of the vehicle models 
or systems listed in the diagnosis section 
due to different countries, areas, and/or 
years. Do not hesitate to contact LAUNCH 
if you come across such questions. We are 
to help you solve the problem as soon as 
possible. 

 

Disclaimer 

 

??

To take full advantage of the unit, you 
should be familiar with the engine. 

??

All information, illustrations, and 
specifications contained in this manual are 
based on the latest information available at 
the time of publication. The right is 
reserved to make change at any time 
without notice.   

 

Summary of Contents for X-431 PADII













Reviews: