Lattice Semiconductor ECP5 Versa Technical Note Download Page 60 | Manualshive

Page: 60 / 86

background image

ECP5 and ECP5-5G High-Speed I/O Interface

Technical Note

© 2014-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at

www.latticesemi.com/legal

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

60

FPGA-TN-02035-1.3

describes the various settings shown in the Configuration tab.

Table 7.6. DDR_MEM Configuration Tab Parameters

User Interface Option

Description

Values

Default

Interface

DDR memory interface type

DDR2, DDR3, DDR3L, LPDDR2, LPDDR3

DDR2

I/O Buffer Configuration

I/O type configuration for DDR
pins

DDR2: SSTL18_I, STL18_II
DDR3: SSTL15_I, SSTL15_II
DDR3L: SSTL135_I, SSTL135_II
LPDDR2: HSUL12
LPDDR3: HSUL12

DDR2: SSTL18_I
DDR3: SSTL15_I

DDR3L: SSTL135_I

LPDDR2: HSUL2

LPDDR3: HSUL12

DDR Memory Frequency

Target DDR memory interface
frequency

DDR2: 125, 200, 267, 333, 400 (MHz)
DDR3: 300, 400
DDR3L: 300, 400
LPDDR2: 125, 200, 267, 333, 400 (MHz)
LPDDR3: 125, 200, 267, 333, 400 (MHz)

DDR2: 267 MHz
DDR3: 400 MHz

DDR3L: 400 MHz

LPDDR2: 400 MHz
LPDDR3: 400 MHz

System Clock Frequency

Calculated system clock frequency.
Not user-selectable, display only.

SCLK Frequency Value

DDR Memory

Frequency/2

Data Width

DDR memory interface data width

DDR2, DDR3, DDR3L: 8, 16, 24, 32, 40,
48, 56, 64, 72
LPDDR2, LPDDR3: 16, 32

16

Number of DQ per DQS

Number of associated DQ per DQS
pin

DDR2, DDR3, DDR3L: 4, 8
LPDDR2, LPDDR3: 8

8

Total number of DQS
Groups

Total number of DQS groups. Not
user-selectable, display only.

Data width/number of DQ per DQS
group

2

DQS Buffer Configuration
for DDR2

DDR2 DQS I/O buffer type
selection

Single-ended, Differential

Single-ended

Clock/Address/Command

Clock/address/command pins
added with this option checked

ENABLED, DISABLED

DISABLED

Data Mask

Data mask pins added with this
option checked

ENABLED, DISABLED

DISABLED

Enable Dynamic Margin
Control on Clock Delay

Dynamic margin control ports
added with this option checked

ENABLED, DISABLED

DISABLED

Generate PLL with this
module

PLL included with this option
checked

ENABLED, DISABLED

DISABLED

PLL Input Clock Frequency

Input reference clock frequency

10 MHz–400 MHz

—

CLKI Input Buffer Type

The I/O Standard for the PLL
Reference Clock.

List of Legal Input Standards,
None (if coming from fabric)

LVCMOS25

Actual DDR Memory
Frequency

Calculated actual memory bus
frequency. Not user-selectable,
display only.

—

—

If you choose to generate the Clock/Address/Command signals, then the settings in the Clock/Address/Command tab
are active and can be set up as required.

«
...
58
59
60
61
62
...
»

Summary of Contents for ECP5 Versa























































































Reviews:

No comments

Related manuals for ECP5 Versa

Brand: JB-Lighting Pages: 60

Brand: DAKO Pages: 25

Brand: 3M ESPE Pages: 50

Brand: VACGEN Pages: 13

Brand: M-system Pages: 5

Brand: MA Pages: 2

Brand: MAHA Pages: 21

Brand: MAGUIRE Pages: 47

Brand: TECshow Pages: 22

Brand: Emos Pages: 8

Brand: Albrecht Pages: 4

MICRO BEAMER RGBW

Brand: Briteq Pages: 16

Brand: Gerber Instruments Pages: 18

Brand: IKEA Pages: 16

SpinVessel 650ml

Brand: V&P Scientific Pages: 9

LED Studio 3300D

Brand: PR Lighting Pages: 16

Brand: Old Town Canoe Co. Pages: 1

Brand: Iwatsu Pages: 234

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands