background image

MSA Latchways

®

 

Vertical Device

 

LadderLatch, TowerLatch, TowerLatch SP and Climblatch 

                                                                                                 

Latchways, an MSA Company.   

5. Pre-use checks

  

 

Always fully inspect the following: 

 

 System tension 

Depending on the type of system tension indicator fitted this can be checked using 1 of 2 methods. 

 

Tenser disk

 

– This is generally located at the bottom of the system on the bottom anchor, when the system is 

correctly tensioned, the disc will spin freely with up to 2 mm of vertical movement. (On some installations the 
tenser disc may be located at the top of the system). 

 

 

 

 

 

 

 

 

 

 

 

Visual tension indicator

 

– This component allows the user to check the system tension in situations where it 

is impractical to reach a tension indicator disc from a position of safety. 
 

 

 

 

 

 

 

 

 

 

 

 

If a fault is identified with system tension the system shall not be used and the issue raised with site supervision. 

 

 

 

 

Tension indicator disc 
(highlighted red for clarity) 

Tension indicator guide 

The system is correctly 

tensioned when the tension 

indicator guide is aligned 

within the rebated area of 

the front plate 

Summary of Contents for Latchways LadderLatch




















Reviews: