background image

Operating Procedures

Recommended Blades

Operating Procedures

Lastec//021819

4-6

4

4.4

Recommended Blades

Ultra Low Blade (Part No. 063265)

Use Ultra Low Lift Blade when the conditions are dry and in sandy soil areas. When con-
ditions like this are evident, lift created by the cutter blades can be reduced, decreasing 
the abrasion wear to the cutter blades and deck caused by sand. The Low Lift Blade will 
also help reduce cutter deck blowout during the conditions stated above. 

Low-Lift Blade (Part No. P-246)

Low-Lift Blade is recommended for 1”-2” cutting height. Use a Low Lift Blade when the 
conditions are dry, the region is experiencing a drought, in sandy soil areas or when per-
forming seasonal scalping. When conditions like this are evident, lift created by the cutter 
blades can be reduced, decreasing the abrasion wear to the cutter blades and deck 
caused by sand. The Low Lift Blade will also help reduce cutter deck blowout during the 
conditions stated above.

High-Lift Blade (Part No. P-128)

High-Lift Blade is recommended for cool season grasses and cut heights of 2” and above, 
unless in sandy conditions. These blades are shipped standard on all mowers.

Use a High Lift Blade when the conditions are extremely wet or heavy. The High Lift 
Blades will create greater lift that may be needed in difficult cutting conditions. Additional 
deck cleaning may be required when using High Lift Blades.

Gator Mulching Blade (Part No. P-322)

Mulching blades are designed for use with a mulching (discharge block-off) plate or with a 
complete mulching system. These blades feature a high lift, “double-cut” edge for quick, 
thorough shredding of grass clippings, leaves and debris. 

Summary of Contents for 621ER




















































Reviews: