background image

 

7

Installing and connecting the door release

The door release is controlled by the relay in the outdoor panel and must be powered from a separate
DC power adapter.
Install the door release in the gate or the entrance door according to the manufacturer's recommendations.
Then proceed to connect the wires in the outdoor panel (two black wires), power adapter wires and
the door release, as shown in the connection diagram (see Figures 6, 7, 8 and 9).

6. Video doorphone operation

- Pressing the calling button on the outdoor panel triggers a calling signal in the monitor and switches
on the camera view (if the additional monitor has been installed, the camera view will display on both
monitors).
- To switch on voice communication, press the button    (talk, see Fig. 1). In two-monitor installations,
if voice communication has been established by one of the monitors, the other one will switch off after
approx. 1 minute.
- If voice communication is not activated after the calling, the monitor will automatically switch off after
approx. 1 minute.

- The talk time is limited to approx. 120 seconds, after which the phone will automatically hang
up.

- To hang up, press the button    (talk) again.
- The door release can be activated at any time during the conversation by pressing the button 
on the monitor. The release continues while the button remains pressed.
- The camera view on the monitor can be switched on at any moment by pressing the button 
(view). Pressing the button again will switch the view to the next entrance, and pressing the button
yet again will switch off the camera view.
- sequential operation. To activate voice communication in the camera view mode, press the button

  (talk).

- To accept a redirected call, press the button    (talk).
- The MVC-6601 monitor features controls for volume, brightness and colour saturation adjustment
(see Fig. 1).

7. Video Doorphone maintance

Components of the video doorphone should be cleaned with a wet cloth or with cleaning
agents designed for plastics.

ATTENTION!

Do not use solvents or abrasive cleaners, as they can result in permanent damage to the surface of
the casing! Avoid any contact of doorphone components with water or cleaning agents, as this might
result in damaging the device and electric shock!

 LASKOMEX PPUH, ul. D¹browskiego 249, 93-231 £ódŸ, tel. (42) 671 88 00, fax (42) 671 88 88, e-mail: [email protected], http://www.laskomex.com.pl

Summary of Contents for Bastion Draco II













Reviews: