MODELO S18355
FUNCIONAMIENTO
Este Ventilador puede hacerse funcionar mediante los
Controles Manuales ubicados en la parte superior de
la unidad (como se muestra en la
Figura 10
) o con el
Control Remoto (se muestra en la
Figura 13
.
1. Conecte el cable eléctrico a un tomacorriente de 120 V~.
2. Conecte la energía eléctrica a su ventilador pulsando el
Botón Alimentación ( ).
3.
VELOCIDAD DEL VENTILADOR:
Ahora puede ajustar
la velocidad del ventilador presionando el botón de
velocidad del ventilador ( ).
4.
OSCILACION:
Empuje la perilla ubicada en la parte su-
perior de la caja del motor para hacer que la cabeza del
Ventilador se mueva de un lugar hacia otro. (Figuras
11 y 12)
5.
Después de apagar el Ventilador, desconecte la unidad
del tomacorriente eléctrico.
New 11/13
10
2084836
New 11/13
3
2084836
1. Take pipe assembly out of carton as shown.
(Figure 1)
2. Loosen
Height Adjustment Nut
turning
counter clockwise
.
(Figure 2)
3. Raise
Extension Pipe
.
(Figure 3)
4. Tighten
Height Adjustment Nu
t
turning
clockwise
.
(Figure 4)
STEP 1: PIPE ASSEMBLY
STEP 2: STAND ASSEMBLY
PLACE BASE FLAT ON FLOOR
1. With a twisting motion, insert the end of the large diameter
pipe into hole in
Base.
(Figure 5)
Turning pipe while pushing
will assure pipe is fully seated in
Base
.
2. For Height Adjustment:
a) Loosen
Height Adjustment Nut.
b) Raise or lower
Extension Pipe
to desired height.
c) Tighten
Height Adjustment Nut
.
1. Place
Head Assembly
with
Collar
onto
Extension Pipe.
(Figure 6)
2. Holding
Extension Pipe
firmly, twist
Head Assembly
downward until seated on
Extension Pipe.
1. Tilt
Head Assembly
back. Put
Rear Grill
on
Head Assembly.
(Figure 7)
2. Align tab of Plastic
Rear Grill
with groove on top of front
Head Assembly.
STEP 4: BLADE & GRILL ASSEMBLY
3. Fully seat
Rear Grill
and secure with
Plastic Nut
turning Clock-
wise. Slide
Blade
onto
Motor Shaft.
(Figure 8)
Align
Groove
on
blade hub with
Pin
on motor shaft.
(Figure 8A)
4. To secure
Blade,
screw Fan
Spinner
onto Shaft
Counter Clockwise
until tight on Blade hub.
STEP 3: HEAD ASSEMBLY
Head
Assembly
Collar
Extension
Pipe
Figure 6
Botón
Alimentación
Figura 10
Figure 2
Figure 4
Figure 3
Figure 1
Height
Adjustment
Nut
Extension
Pipe
Rear
Grill
Figure 7
Rear Grill
Figure 8
Blade
Fan
Spinner
Plastic
Nut
Figure 8A
Pin
Groove
Hacia Arriba: Estacionario
Hacia Adelante: Oscilar
Figura 11
Figura 12
Botón
Velocidad del
Ventilador
Figure 5
Extension Pipe
Height
Adjustment Nut
Base
5.
With fan head in upright position, align Ornament of Front Grill
so it is horizontal and right side up. By starting with the top of
the grill and working down, insert Snaps on Rear Grill through
Slots in Front Grill.
Do Not
take pipe apart. Should pipes become separated, insert
pipe A into pipe B.
A
B
Head
Assembly
Larger
Pipe