NEW 2/20
2
CT22445ES
SAVE THESE INSTRUCTIONS
Read all instructions before using this Heater.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fire, electrical shock and injury to persons:
CAUTION
• Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so the Heater or other objects
are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners, or similar coverings as this may cause cord to overheat.
Arrange Power Cord away from room traffic and where it will not be tripped over.
• This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear.
• This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER locate a
Heater where it may fall into a bathtub or other water container.
• DO NOT use Heater outdoors.
• This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC)
Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings.
THIS HEATER DOES NOT MEET THE RE-
QUIREMENTS OF NEC ARTICLE 547-7 (2008).
• This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating
to electrical requirements for Hazardous locations.
THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).
• Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Heater. If this occurs, move the Heater to another location.
• Keep Heater remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Heater.
Model CT22445
Lasko Products, LLC
820 Lincoln Avenue
West Chester, PA
19380
www.lasko.com
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
“NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and the receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.”
WARNING
WARNING
• PLUG HEATERS DIRECTLY INTO A 120V WALL OUTLET/RECEPTACLE ONLY. NEVER USE WITH AN EXTENSION CORD. DO NOT
PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE OUTLET
ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. DO NOT
PLUG MULTIPLE DEVICES IN THE SAME OUTLET OR ON SAME CIRCUIT AS HEATER.
• FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG FITS TIGHTLY
INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING. IF NECES-
SARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. DO NOT USE THIS HEATER WITH ANY SOLID
STATE SPEED CONTROL DEVICES.
• Make certain that the power source conforms to the electrical requirements of the Heater.
• Extreme caution is necessary when any Heater is used by or near children or invalids. The Heater should not be left operating unattended.
Never leave children unattended when the Heater is on or plugged in.
• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Do not attempt to defeat this safety feature.
• DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use Heater in locations where
flammable or explosive chemicals are stored, or in wet atmospheres.
• Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner.
To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.
• Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
• Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or damage
the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
• Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. Do not
depend on the on/off switch as the sole means of disconnecting power when servicing or moving the Heater. Always unplug the power cord.
NEW 2/20
7
CT22445ES
Partes Incluidas
1
2
TERMOSTATO AUTO ECO
™
Al presionar los botones ( ) o ( ) mientras se encuentra en las configuraciones de energía ALTA o BAJA, se encenderá la función Auto Eco
™
.
1. Para fijar una temperatura específica en la habitación, presione los botones ( ) o ( ) hasta la temperatura deseada. La temperatura destellará. El
calefactor está ahora en modo Auto Eco
™
.
2. Cuando se alcance la temperatura en la cual desea establecer la unidad, la temperatura fijada destellará varias veces y luego la pantalla volverá
a indicar la temperatura ambiente actual y cambiará gradualmente a medida que cambie la temperatura ambiente. NOTA: La pantalla de la tem-
peratura no indica la temperatura del aire caliente que emite el calefactor.
3. Una vez que la temperatura ambiente alcance 2 grados por encima de la temperatura fijada, el calefactor se apagará. El calefactor continuará
operando durante 15 segundos después de que el elemento se ha apagado.
4. Si la temperatura ambiente es igual a la temperatura FIJADA, el calefactor operará en calor BAJO.
5. Si la temperatura ambiente es menos de la temperatura FIJADA en más de 3 grados, el calefactor operará en calor ALTO.
Todo esto ocurre automáticamente con la tecnología Auto Eco
™
de Lasko.
Para desactivar la función Auto Eco
™
, apague el calefactor o presione el botón (
).
NOTA:
En el modo Auto Eco
™
, el Calentador mostrará la temperatura ambiente actual en grados Fahrenheit. Presione los botones ( ) y ( ) al mismo
tiempo para mostrar los grados Celsius. Presione los mismos dos botones juntos nuevamente para volver a mostrar los grados Fahrenheit.
CONTROL REMOTO
Todas las funciones realizadas con el Control Remoto operan del mismo modo que los controles manuales, excepto que usted no puede cambiar de °F
a °C con el control remoto.
1. El control requiere 2 baterías AAA de 1.5 Vcc (incluidos). Instale las baterías como se indica la polaridad.
2. No mezcla baterías viejas y nuevas. No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (níquel-cadmio).
3. No arroje las baterías al fuego, las baterías pueden estallar o puede derramarse el líquido contenido.
4. Siempre compre el tamaño y grado correctos de la batería más adecuada para el uso previsto.
5. Limpie los contactos de las baterías y los del dispositivo antes de la instalación de las baterías.
6. Retire las baterías del equipo que no se vaya a utilizar por un período extendido.
7. Retire las baterías si se han descargado o si el producto no se va a utilizar por un largo tiempo.
8. Retire las baterías usadas de inmediato.
Si usted pierde su mando a distancia, por favor Cliente de llamada Serive para ordenar un reaplacement en (800) 233-0268, de lunes a viernes, entre las
8 a.m. y las 5 p.m. (Horario Estándar del Este de los Estados Unidos).
Controles
3
1.5V AAA
1.5V AAA
3 Baterías
1 Cuerpo
2 Control
Remoto
* Botón Auto Eco
™
(-)
Presione para Disminuir la temperatura ambiente deseada.
* Botón Auto Eco
™
(
+
)
Presione para Aumentar la temperatura ambiente deseada.
Botón de Modo de Calor
El calor se puede ajustar a H3 (Alto), H2 (Medio) o H1 (Bajo).
Botón de Oscilación de Base
Presione para Iniciar/Detener la función de oscilación de la base.
Botón de Temporizador
El temporizador se puede configurar para 8 horas. Continúe pul-
sando el Botón del Temporizador para llegar a la configuración
de tiempo deseada. La luz se vuelve verde cuando se activa.
Botón de Encendido
ENCENDIDO/APAGADO el Calefactor presionando
el Botón de Encendido.
