Rev. A 10/10
4
4443ES
MODEL 4443
This Fan may be operated by the local controls located on
top of the unit (as shown in
Figure 4
or by the Remote Control
(shown in
Figure 5
).
1. Place the Fan on a firm and level surface.
CAUTION:
Plastic or rubber tabs, like the feet on this unit,
may stick to furniture surfaces and/or hardwood floors. The unit
may leave a residue that could darken, stain or leave permanent
blemishes on the finish of certain furniture surfaces, including wood
surfaces, and/or hardwood floors.
2. Plug the cord set into a 120 V~ outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they may
slip partially or completely out of the receptacle with
only the slight movement of the attached cord. Re-
ceptacles in this condition may overheat and pose a
serious fire hazard; if covered by a curtain or drape,
the fire hazard is even greater.
3. Turn on the Fan by pressing the
Power Button
( ) on the unit
or the remote control.
4.
SPEEDS:
Adjust the speed of the Fan by pressing the
Fan
Speed Button
( ) after the power is turned on. Each time the
speed button is pressed, the speed will change, from High (3),
to medium (2), to Low (1).
5.
OSCILLATION:
With the Fan on, press the
Oscillation Button
( ) to
start and stop the oscillation function. The oscillation function
can be used in any speed.
6.
NIGHTLIGHT:
Press the Nightlight Button ( ) to turn on and off
the light at the base of the Fan. The nightlight function will work
when the Fan is ON or OFF.
7.
To turn the Fan OFF, press the
Power Button
( ) and unplug
the unit from the electrical outlet.
OPERATION
(Figure 4)
Figure 4
Oscillation
Button
Power
Button
Night Light
Button
Fan Speed
Button
Rev. A 10/10
9
4443ES
HERRAMIENTAS NECESARIAS PARA EL
ARMADO
(no incluida)
- destornillador de Cabeza Phillips # 2
MODELO 4443
Figura 2
4. Alinee la
Montura de la Base de Apoyo
con la
Base del Motor
,
teniendo en cuenta que la ranura del cable en la parte inferior
de la montura de la base de apoyo debe apuntar hacia la
parte posterior del Ventilador. Adose la
Montura de la Base
de Apoyo
a la
Base del Motor
con
(4) Tornillos Largos M5 de
1/2".
Cerciórese de alinear la
Llave
del
Conjunto de la Base
de Soporte
con la
Muesca Localizadora
de la
Base Del Motor
.
(Figura 1)
Suavemente tire del
Cable Eléctrico
para evitar que
quede flojo y colóquelo en el
Orificio de Colocación del Cable
.
(Figura 3)
ARMADO
1. Para un armado más sencillo, deposite el Ventilador hacia abajo
para que la parrilla frontal y el panel de control apunten hacia
arriba.
2. Arme las mitades de la Base de Apoyo encastrando las
Puntas
de
la
Base de Apoyo A
con los Orificios para
Puntas en la Base de
Apoyo B
. Conecte el
Cable Eléctrico
a través del orificio grande
en el centro de la
Montura de la Base de Apoyo
.
(Figura 1)
3. Asegure
(4) #8 X 1/2" Tornillos
en los dos orificios externos en
la parte inferior de la
Base
cuando mostrado.
(Figura 2)
Puntas de la Base
de Apoyo A
Puntas de la Base
de Apoyo B
Puntas
Figura 1
Cable Eléctrico
Orificio de
Colocación
del Cable
Tornillos
Largos M5
de 1/2"
Figura 3
Montura de la
Base de Apoyo
Puntas de la Base
de Apoyo A
Puntas de la Base
de Apoyo B