Manual
4 / 7
Revision: Apr-10
“LCD display memory function“:
save settings automatically.
Laser: On/Off, when set to Off, laser is off in Auto/DMX mode (ILDA mode only)
X/Y-Axis: mirrors projection horizontally/vertically
Upside down: Display turned upside down
ILDA mode
When an ILDA compatible interface is connected to the laser, the laser is automatically switched to ILDA mode.
Output is then controlled from a PC running software. The laser uses pins 4 and 17 of the ILDA signal to detect
the presence of an ILDA interface. Further information can be found in the software manual.
Please note:
the scanners are set to a scanspeed of ca. 22000 PPS at ca. 30° scanangle. If you increase the
scanspeed, first reduce the scanangle (image size). Otherwise you may damage the scanners! When using with
different scanspeed/scanangle readjustment of the scanner drivers may be necessary, if in doubt, contact your
dealer.
DMX mode
Channel
DMX512 value
Function
1
Red
0~255
0~100% Dimmer
2
Green
0~255
0~100% Dimmer
3
Blue
0~255
0~100% Dimmer
4
Colour
0~25
Original colour
26~51
White
52~77
Yellow
78~103
Red
104~129
Green
130~155
Cyan
156~181
Blue
182~207
Purple
208~233
Change colour
234~255
Colour flux, slow to fast
5
Pattern group
0~51
Pattern group 1
52~103
Pattern group 2
104~154
Pattern group 3
155~205
Pattern group 4
206~255
Pattern group 5
6
Pattern
0~255
160/5=32pcs
7
Horizontal rotation
0~255
slow to fast
8
Vertical rotation
0~255
slow to fast
9
Rotation about Z-axis
0~255
slow to fast
10
Horizontal movement
0~255
slow to fast
11
Vertical movement
0~255
slow to fast
12
Horizontal size
0~255
slow to fast
13
Vertical size
0~255
slow to fast
14
Hor. and vert. size
0~255
slow to fast
15
Drawing speed
0~255
slow to fast
16
Point draw
0~255
slow to fast
17
Scanspeed
0~255
slow to fast
18
Pattern size
0~1
Original size
2~255
Size (120=original)
Maintenace / cleaning
Always disconnect from mains before cleaning/opening the laser. You can open the device by removing the top:
remove the mounting bracket (4 quick locks), the 5 Philips screws, and the eye bolt.
Regularly clean the interior from dust, especially ensure operation of the fans. To clean the mirrors, ideally use
acetone and lens cleaning paper (fold paper to get an edge with which to clean the mirrors). If not available, you
can also use window cleaner, and a paper towel. Be careful, even light scratches reduce the output power of the
laser; always clean with strokes in one direction, to minimize the effect of scratches. Mirrors need cleaning, when a
“halo” is noticeable around the beam, or an unusual high amount of diffuse light can be seen inside the device.
When fog fluid condenses in the device, clean all traces, and rearrange the position of fazer and/or laser.
Technical specifications
Output power (in mW, at the laser):
max 7000mW, >1500mW 655nm red, >1200mW 532nm green,
>2000mW 445nm blue
Lasersources:
aircooled DPSS laser (green), laser diode (red, blue)
Laser class:
4
Modes:
ILDA, DMX 512, auto
ILDA:
ILDA standard Sub-D shaped 25pin connector
Galvos:
max 50k scanspeed (at 4°)
DMX 512:
18 channels
