background image

 User manual: CS-400RGB 

Rev: 02/2009 

page8 of 8 

EU-declaration of conformity 

 
 

We hereby confirm that the following device 
 

Laserworld CS-400RGB

 

 

complies with the essential safety requirements, laid down in the regulations of the 
committee to assimilate the provisions of law of all participating EU states on the 
electromagnetic compatibility (89/336/EWG). 
The device has been classified considering the following EU-norms on 
electromagnetic compatibility: 
 
DIN EN 61000-3-2:2000 + A2: 2005 
DIN EN 61000-3-3:1995 + A1: 2001 

 

Assessment of compliance of the product with the requirements relating to the Low Voltage 
Directive (LVD 2006/95/EG) was based on the following standards: 
 
DIN EN 60065 : 2002 

 

Furthermore, the device is verified in correspondence to the laser class regulations DIN EN 
60825-1, if properly set up according to the upper mentioned laser safety regulation. 
After installing the device, an inspection and official approval is indispensable for the overall 
setup. The inspection must follow the european guidelines EN 60825-1 and corresponding 
regulations for the prevention of accidents BGV-B2.  
 
This declaration is executed on behalf of the Laserworld CS-400RGB manufacture 
 

 

 

Laserworld (Switzerland) AG

  

  
Oberstrasse 1  
8274 Tägerwilen  
SWITZERLAND  
   
Authorized person:  
Supervisory board Ms Rhea Gössel  
  
place of business:

 

8274 Tägerwilen / SWITZERLAND 

company number: CH-440.3.020.548-6  
Commercial Registry Kanton Thurgau 
 
www.laserworld.com 
[email protected] 
 
representative according to EMVG: 
Cleantech Europe GmbH 
Managing Director: Thomas Schulze 
Fürkhofstr. 5 
81927 München / DE 

Summary of Contents for CS-400RGB









Reviews: