background image

 User manual: CS-400RGB 

Rev: 02/2009 

page4 of 8 

Keep surrounding dry and clean. T

his unit should be kept dry, do not use in the rain 

or damp and dusty environment. Projector should be put in a water-proof housing 
when operated outside.  
Operating temperature is 10~35

°C

. Let laser cool off 10minutes after 2 hours of 

operation, to ensure maximum lifetime for the diode. 
Distance between laser aperture and projection screen should be not less than 1 
meter. 

Do not turn device on and immediately off again frequently. 
Do not look into the laser beam directly, especially not with optical instruments. 

Do not touch the device with wet hands. 

When the laser diode becomes dim or broken, please contact your dealer timely. 

When returning laser to dealer/manufacturer always use original packaging.

 

Maintenance should be performed every 15-day period. Use a sponge with alcohol, 
rather than wet cloth or other chemical liquid, to clean the mirror. 

1.

 

 

Inbetriebnahme 

Make sure the correct voltage is used. Connect mains. Connect an emergency switch 
to the 9-pin connector on the backside (pins 1, 2). If you do not wish to connect an 
emergency switch, connect the 9-pin plug. Depending on the mode selected (see 
below), laser light should come out of the 
opening on the front panel – be careful. 

Control panel 

Microphone 

Safety switch: laser on/off 

ILDA connector 

Operating modes 

The following operating modes can be selected from the DIP switch on the backside 
of the device: 
DIP switch 1-10 

Mode 

0,0,0,0,0,0,0,0,0,0 

Music activ 

1,0,0,0,0,0,0,0,0,0 

Automatic mode / beameffects 

1,1,0,0,0,0,0,0,0,0 

Automatic mode / graphics 

x,x,x,x,x,x,x,x,x,1 

DMX 

 

Power switch: power on/off 

Remotelock: connect emergency switch. If 
no emergency switch is connected use the 
9 pin plug supplied. 

DIP switch: DMX address/mode selection 
(see below) 

DMX 512 in/out 

Music mode: sensitivity 

Summary of Contents for CS-400RGB









Reviews: