Laser Reference ProShot L5 Operation Manual Download Page 7

Maintenance

Calibration
There is no set interval for checking the calibration of the  L5, but  
calibration should be checked from time to time in order to ensure that 
the highest possible quality of work is being done.  Calibration should 
always be checked if the laser has been handled roughly or shipped by 
common carrier.

Batteries
From time to time, remove the batteries and check the contacts for 
corrosion.  Alkaline batteries will last far longer than carbon batteries.  If 
you use Ni-Cd rechargeable batteries, be careful to never charge alkaline 
or carbon batteries.  Also, do not charge Ni-Cd batteries too often.  Ni-Cd 
batteries should be charged after about 20 to 24 hours of operation.   
Never run the laser from the charger unless there are rechargeable (Ni-
Cd) batteries installed.  Keep a spare set of batteries in the carrying case 
to avoid down time.

Laser output windows
Regularly check the output windows for dust and dirt.  Dust can be 
removed with a camera brush or clean compressed air.

Control panel and exterior
Clean the control panel and the other exterior surfaces of the laser with a 
soft damp cloth. 

Tripod mounting thread
Occasionally, the threaded hole for the tripod bolt should be lubricated 
with a light oil.

Caution
Never store the laser in a carrying case that is wet inside.  Moisture can 
get inside the laser this way.  Should this happen, remove the battery 
cover and place the laser and the open case in a warm area until it is 
completely dry (free of condensation inside windows).

5

12

Accessories - Receivers

When your work takes you outdoors, a receiver is essential.  No true 
rotating laser can be used outdoors without a receiver as it would not be 
safe or legal to put out enough laser power to make the rotating beam 
visible in sunlight.  There are two receiver choices available, the basic 
R6 receiver and the more capable R7.  

For most needs, the R6 is the recommended choice.  It provid es 
excellent functionality at a great price.

•  1.5" reception height

•  Three channel LCD front display

•  Selectable tone (hi, low, off)

•  Battery life 70 hrs. (2 AA batts.)

•  90

º

 reception angle

•  One year warranty

If your work demands more capability and flexibility, 
the R7 is our top of the line receiver.

•  2" reception height

•  Five channel display

•  Front and rear displays

•  Three accuracy selections

•  Loud tone (selectable)

•  120

º

  reception angle

•  Three year warranty

Summary of Contents for ProShot L5











Reviews: