background image

Issue 1

Page 13 of 24

EL-SMS-2G-TP / TP+ / PROBE-G USER MANUAL

Run Mode

Following a successful configuration of the unit it will enter into Run mode. In this
mode the unit checks to see whether any notification messages are due to be sent
(i.e. alarm breach, battery low or summary notifications) and then processes the
notifications in order of their priority:

 

Temperature alarms have the highest priority

 

Low battery alerts have medium priority

 

Summary messages have the lowest priority

In Run mode the temperature is measured once every minute using the external
probe and the value is checked to see whether either the upper or lower
temperature alarm limits have been breached. If an alarm limit is breached (see

alarm delay operation) the unit will send an alert notification message to the

contacts registered to receive the “alarm” group messages.

The battery condition is checked each time a temperature measurement is made.

If a low battery condition is detected a battery low notification message will be sent.

The buttons are disabled whenever the unit is actively sending an SMS.

Stop Monitoring

When the unit is in Run mode it can be put back into a Standby mode by pressing
the “Stop monitoring” button combination. This should be done whenever you want
to stop the unit from monitoring the temperature and sending alert messages.

To stop the unit, press the status button for five seconds whilst holding down the

“Stop” button for at least one second. The unit will show the green LED for three
seconds after which it will reset. The power up LED sequence will then be displayed

User Guide

and the unit will be in the standby mode in an “unconfigured” state.

To start monitoring again you will need to repeat the setup process.

SMS Retry Process

Start SMS alert

Alert success

Continue monitoring

Allow up to 2 minutes to register on mobile network

Success/Failure?

No

Yes

No

Yes

Make 2 attempts to send alert to each stored number

At least 1 SMS

delivered to network?

Was this a

retry attempt?

5 Minute holdoff

period then retry

attempt.

No more retries.

Alert failure. Alert will

be dropped.

Summary of Contents for EL-SMS-2G-TP


























Reviews: