background image

The instructions are split into two sections: 

RECESS INSTALLATION, PAGE 2,

 and  

SURFACE INSTALLATION, PAGE 6

. Determine which you need before starting.

Please contact your LARSON Dealer for additional custom sizes and colors.

INSTALLATION TOOLS

I T   I S   H I G H LY   R E C O M M E N D E D   T H A T   T H E   I N S T R U C T I O N S   B E   R E A D   T H R O U G H   B E F O R E   I N S T A L L A T I O N .

PHILLIPS SCREWDRIVER

MEASURING TAPE

HAND-HELD OR POWER SAW

POWER DRILL & BITS

RUBBER MALLET

Use saw  
blade suitable 
for cutting 
aluminum.

SCREENED PORCH • GAZEBOS • GARAGE OPENINGS 

INSTALLATION INSTRUCTIONS

LARSON GRANDVUE 800 INSTRUCTIONS

  •  PART NUMBER : 202220701-0121

Larson Retractable Screens provide insect protection and support fresh, natural ventilation in low-wind conditions. Unlike 4-sided rigid framed screens, Larson 
Retractable Screens move in and out of a protective cassette and the exposed surface area and edges of the fabric are flexible.  Consequently, the wind speed that a 
retractable screen can withstand (e.g. before the edges of the screen fabric may push out of the guide rails), will depend on the width and height of the opening, the 
openness factor of the specific screen fabric and, other design factors of the model.  Retractable screens are not to be kept open or continually exposed to wind, sun, 
rain or other harsh conditions. Please be sure to use your retractable screen only during low-wind conditions.

NEEDLE PLIERS

PENCIL OR PEN

Summary of Contents for GrandVue 800












Reviews: