EXPCMR-ALG-1080P-IC-16.7-25-L21.20-1227
Larson Electronics, LLC
Phone: (800) 369-6671
Fax: (903) 498-3364
www.larsonelectronics.com
2
of
7
WIRING
Link-up with the camera is achieved via 25` 16/5 SOOW cord terminated in a L21-20P twistlock cord cap. The cable is ran back to
the Larson Electronics DVR system (MDVR-ALG series, sold separately), located outside the hazardous location. The portable DVR
system allows operators to temporarily mount the explosion proof camera without the need for running conduit or cable. The DVR
system handles signal and provides power to the camera. The twistlock connector ensures the camera does not come unplugged
during operation.
We strongly encourage a licensed electrician install this product
, in all locations especially in outdoor areas
where weatherproofing may be required. Universal voltage driver permits operation at 100V - 277V AC, 50 or 60Hz
except those factory ordered with low voltage 11V to 25V AC/DC.
Warning:
Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in the diagram
Secure each pair of wires according to the diagram. Utilize a junction box or
similar device and take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.
The EXPCMR-ALG-1080P-IC-16.7-25-L21.20-1227 explosion proof high definition analog camera from Larson Electronics is an
inspection camera that can be used for remote observation in hazardous locations. It is available in a fixed lens configuration, a 3.6mm
90° lens to capture large wide areas, and can produce an image up to 1080p resolution. The EXPCMR-ALG-1080P-IC-16.7-25-
L21.20-1227 allows operators to see visual process data from a centralized control room up. This temporary camera allows operators to
use a single cable for signal and power. Equipped with 25` SOOW cord, this portable explosion proof camera is ideal for temporary
installation for inspection, tank cleaning, and any application requiring a portable camera within hazardous locations.
MOUNTING
The EXPCMR-ALG-1080P-IC-16.7-25-L21.20-1227 explosion proof remote observation camera is typically mounted to flat
surfaces for observation. The included adjustable flat surface bracket has two set screws on the bracket, allowing operators
to loosen the mounting bracket, adjust the camera`s tilt orientation, and retighten to hold the camera in position. A single
thru-hole mounting bolt allows operators to adjust the rotation of the camera by loosening one bolt. Accessory pole mounts
and magnetic mounts are available.
Exp Cord Cap
Position device near work area for operation. Run cable to nearby power
source. Insert and twist-lock explosion-proof plug into a compatible receptacle within
the hazardous environment. See
plug operation
below.
PLUG OPERATION
Electrical connection between plug and compatible receptacle is accomplished
after plug fully inserts into receptacle and rotated clockwise.
1.
Lift receptacle door and locate polarization on mating plug pin and
receptacle face. Insert plug straight all the way into receptacle until it
cannot go further.
2.
Rotate plug clockwise limit (37º), this closes internal contacts and
completes circuit. This also mechanically locks plug into receptacle so it
cannot be pulled out.
3.
To remove plug, push plug inward and turn to counterclockwise, pull plug
straight out.
NOTE:
This product does
NOT
use a standard L21-20 plug and
CANNOT
be plugged into standard L21-20R receptacles.
This product is designed to pass power and signal through the plug for easy disconnects. Users
MUST
wire the L21-20R
receptacle to the correct voltage and utilize a BNC-ALG-SGL-XMFR signal converter on the output side. See Wiring diagram
for plug pinout.
