EPL-48-2L-T12VHO
Larson Electronics, LLC
Phone: (800) 369-6671
Fax: (903) 498-3364
www.larsonelectronics.com
2
of
3
WIRING
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product
, in all locations especially in outdoor areas
where weatherproofing may be required. Universal voltage driver permits operation at 1
2
0V
OR
277V AC
.
Warning:
Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in the diagram
Secure each pair of wires according to the diagram. Utilize a junction box or
similar device and take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.
ADJUSTABLE SURFACE MOUNTING BRACKETS
Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by tightening
two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single
bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a
surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the
bracket to the mounting peg.
SUSPENSION MOUNTING
Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each fixture features a 1/2” NPT junction box
on one end, and a 1/2” NPT adjustable L-bracket on the other end of the fixture. Operators bring rigid pipe down to the
threaded mounting hubs. Wiring is fed down through the rigid pipe to the junction box and tied in to the fixture’s lead wires,
completing the electrical connection. The adjustable L-shape mounting bracket provides support for the opposite end of the
fixture.
INSTALLATION
We strongly recommend that only a licensed electrician install this product.
Warning:
Make sure that the power is disconnected before installing. This fixture is extremely heavy and must be
mounted to a surface that can structurally support the load. Note: this fixture requires a minimum of 50 inches of
clearance from re-lamp end for lamp replacement. An optional drop mounting kit that will allow for end to end row
mounting is available, please consult factory.
Warning: Do not let fixture hang on one bracket at any time. Failing to comply can result in breakage of and end
casting or mounting bracket allowing the fixture to fall which can cause serious injury or death.
•
The mounting brackets are shipped installed on the fixture.
•
Install the brackets to wall or ceiling with two 3/8’’ bolts (not supplied) at center
measurements.
•
Fixture is now ready for mounting.
It is strongly suggested to use two licensed electricians to proceed with the final mounting of the fixture to
avoid any possible personnel injury or damage to the fixture as the unit weights up to 66lbs (30.0 kg) and will
be slightly awkward to hold in position and
attach to brackets mounted on wall or ceiling. Depending on
mounting height and scaffolding, a hydraulic man–lift or two good quality ladders should be used.
•
Remove the upper center screw cap on the re-lamp end (field wiring
compartment).
•
Install approved cable connector or conduit fitting into ½’’ npt hub on field wiring
compartment.
•
Install a three conductor cable into the connector, allowing 3 inches of wire inside
compartment for connection.
•
Using approved wire connectors, splice wires as per color codes: black to black
(line) white to white (common) and green to green
(ground).
•
Replace end-cap, making sure there are no wires protruding that maybe pinched
causing a possible short circuit.
Warning: Fixture must be grounded as required per paragraph 410-21 and article 250 of
the National Electric Code and/or rule 30-500. Failure to properly ground this fixture will
create and electrical shock, which can cause serious injury or death.
WIRING INSTRUCTIONS