Larsen & Brusgaard Military ALTITRACK Instruction Manual Download Page 42

Page: 42 / 46

23 - Military ALTITRACK IrDA Transceiver

23.1 Enable the Military Altitrack IrDA port on the ground

Military Altitrack in Sleep Mode

Press and hold Left Front Button for 3 sec.

The OLED displays

“IR Active”

and communication is enabled for 2 minutes. During this period

the ALTISET can be used to transmit data.

To disable the IrDa port within 2 minutes, press and hold Left Front Button for 5 sec

23.2 Enable the Military Altitrack IrDA port in the aircraft

Military Altitrack in Jump Mode

The Military ALTITRACK IrDA port is always active in Jump Mode.

23.3 ALTISET Programming

Press

to activate ALTISET

Adjusting mBar, Backlight and Backlight Intensity

Press

again to select mBar. Press

to adjust the mBar. Then press

Press

to go to the next menu point (Backlight)

Press

to select Backlight ON/OFF

Press

to select next menu point (Backlight Intensity)

Press

and then

to set Backlight Intensity. Then press

23.4 ALTISET Data Transmission to Military ALTITRACK

Press and hold

3 seconds. “LINKED” light starts flashing and display shows

“Searching for

AltiTrack”.

The ALTISET is searching for connection with Military ALTITRACK every 4 seconds.

Point ALTISET towards the IrDA transceiver and within 4 seconds the data will be transmitted
and briefly confirmed on the Military ALTITRACK OLED.

The ALTISET will keep searching for IrDA transceivers for 2 minutes each time it has transmitted
data.
ALTISET enters sleep mode if no IrDA transceivers are found within 2 minutes.

Summary of Contents for Military ALTITRACK















































Search results

Summary of Contents for Military ALTITRACK

Reviews:

Related manuals for Military ALTITRACK

Brands by name

Popular brands

Larsen & Brusgaard Military ALTITRACK, Instruction Manual

Search results

Summary of Contents for Military ALTITRACK

Reviews:

Related manuals for Military ALTITRACK

Brands by name

Popular brands