background image

7

English

PLA SPRAY GUN

•  THE EMPLOYER SHALL TRAIN ITS EMPLO-

YEES ABOUT ALL THOSE RISKS STEMMING 
FROM  ACCIDENTS,  ABOUT  THE  USE  OF 
SAFETY DEvICES FOR THEIR OWN SAFETY 
AND  ABOUT  THE  GENERAL  RULES  FOR 
ACCIDENT  PREvENTION  IN  COMPLIANCE 
WITH  INTERNATIONAL  REGULATIONS  AND 
WITH THE LAWS OF THE COUNTRY WHERE 
THE PLANT IS USED.

•  THE BEHAvIOUR OF THE EMPLOYEES SHALL 

STRICTLY  COMPLY  WITH  THE  ACCIDENT 
PREvENTION AND ALSO ENvIRONMENTAL 
REGULATIONS IN FORCE IN THE COUNTRY 
WHERE THE PLANT IS INSTALLED AND USED.

SAFEtY RULES

F

•  KEEP YOUR WORK PLACE CLEAN AND TIDY. 

DISORDER WHERE YOU ARE WORKING CRE-
ATES A POTENTIAL RISK OF ACCIDENTS.

•  ALWAYS KEEP PROPER BALANCE AvOIDING 

UNUSUAL STANCE.

•  BEFORE USING THE TOOL, ENSURE THERE 

ARE NOT DAMAGED PARTS AND THE MACHI-
NE CAN WORK PROPERLY.

•  ALWAYS  FOLLOW  THE  INSTRUCTIONS 

ABOUT SAFETY AND THE REGULATIONS IN 
FORCE. 

•  KEEP THOSE WHO ARE NOT RESPONSIBLE 

FOR THE EqUIPMENT OUT OF THE WORK 
AREA. 

• 

NEVER 

EXCEED  THE  MAXIMUM  WORKING 

PRESSURE INDICATED. 

• 

NEVER 

POINT THE SPRAY GUN AT YOURSEL-

vES OR AT OTHER PEOPLE. THE CONTACT 
WITH THE  CASTING  CAN  CAUSE  SERIOUS 
INJURIES. 

•  IN CASE OF INJURIES CAUSED BY THE GUN 

CASTING, SEEK IMMEDIATE MEDICAL ADvICE 
SPECIFYING THE TYPE  OF THE  PRODUCT 
INJECTED. 

NEVER 

UNDERvALUE A WOUND 

CAUSED BY THE INJECTION OF A FLUID. 

•  ALWAYS  DISCONNECT  THE  SUPPLY  AND 

RELEASE THE PRESSURE IN THE CIRCUIT 
BEFORE PERFORMING ANY CHECK OR PART 
REPLACEMENT OF THE EqUIPMENT.

•  NEvER  MODIFY  ANY  PART  IN  THE  EqUIP-

MENT.  CHECK  REGULARLY  THE  COMPO-
NENTS OF THE SYSTEM. 

 

REPLACE THE PARTS DAMAGED OR WORN.

•  TIGHTEN AND CHECK ALL THE FITTINGS FOR 

CONNECTION  BETWEEN  PUMP,  FLEXIBLE 
HOSE AND SPRAY GUN BEFORE USING THE 
EqUIPMENT.

•  ALWAYS USE THE FLEXIBLE HOSE SUPPLIED 

WITH STANDARD KIT. THE USE OF ANY AC-
CESSORIES OR TOOLING OTHER THAN THO-
SE RECOMMENDED IN THIS MANUAL, MAY 
CAUSE DAMAGE OR INJURE THE OPERATOR.

 
•  THE  FLUID  CONTAINED  IN  THE  FLEXIBLE 

HOSE CAN BE vERY DANGEROUS. HANDLE 
THE  FLEXIBLE  HOSE  CAREFULLY.  DO  NOT 
PULL  THE  FLEXIBLE  HOSE  TO  MOvE  THE 
EqUIPMENT. NEvER USE A DAMAGED OR A 
REPAIRED FLEXIBLE HOSE.

Read carefully and entirely the following 
instructions before using the product.
Please save these instructions in a safe 
place.

The  unauthorised  tampering/replace-
ment of one or more parts composing the 
machine, the use of accessories, tools, 
expendable materials other than those 
recommended by the manufacturer can 
be a danger of accident. 
The manufacturer will be relieved from 
tort and criminal liability.

Summary of Contents for AIRLESS PLA K11435













Reviews: