background image

FMT- 25 VHF FM TRANSLATOR                                                              862-09725 

Issue 1A: 

 

TX PLL LOCK (green led) 

ON 

RF FAULT (red led) 

ON 

VSWR FAULT (red led) 

OFF 

TEMP FAULT (red led) 

OFF 

TL ID (yellow Led) 

OFF 

AC SUPPLY (green led) 

ON 

EXT DC (green led) 

ON 

RX PLL LOCK (green led) 

ON 

MUTE (red led) 

OFF 

PROGRAM LOSS (red led) 

OFF 

PSU FAULT (red led) 

OFF 

 

 

c)  ALC METER (not fitted on this unit).

 

 
 
d)  MULTIMETER

 

Select the four functions in turn and check the meter readings:

 

• 

FIELD 

 

 

Indication of received RF level.   

 

• 

FORWARD POWER 

0 Watts (no Leds on).   

• 

REFLECTED POWER 

0 Watts (no Leds on).

   

• 

BASEBAND 

 

 

Indication of received RF level. 

   

e) 

SETTING THE RF POWER LEVEL

  

 

Select FWD POWER on the Multimeter and observe the reading.   
Adjust the Front panel TX PWR ADJ potentiometer clockwise to set the RF output power to 
25W. (This should be achieved with 16 Leds on). 
Now check the PA CURRENT and REFL POWER readings: 
  
PA CURRENT should be approximately 1.9 Amps. 
REFL POWER should be less than 2.5W (16 Leds). 
 
Check all the fault Leds on the front panel and ensure that there are no

 red Leds

 on .  

The unit is now operational and only the final temperature must be monitored after 
approximately 15 minutes. The temperature reading on the front panel Multimeter should 
settle down to approximately 12

°

C above Room temperature. 

 
 

MECHANICAL  
The unit is designed to fit in a standard 19 inch rack, cabinet structure. There is a Slide rail kit 
(option) available for this purpose which allows the unit to be installed in this manner. 

Due to the weight of the  unit it is not recommended to mount the unit without proper 
support.  

 

INTERCONNECTIONS 

Summary of Contents for FMT-24






















































Reviews: