background image

5. Mount the sleeve by inserting the sleeve

into the opening of the dashboard and
bend open the tabs located around the
sleeve with a screwdriver. Not all tabs
will be able to make contact, so
examine which ones will be most
effective. Bending open the appropriate
tabs behind the dashboard to secure
the sleeve in place.

6. Reconnect the wire harness and the

antenna and be careful not to pinch
any wires or cables.

7. Slide the unit into the sleeve until it

locks into place.

8. To further secure the unit, use the

supplied metal strap to secure the back
of the unit in place. Use the supplied
hardware (Hex Nut (M5mm) and Spring
Washer) to attach one end of the strap
to the mounting bolt on the back of
the unit. If necessary, bend the metal
strap to fit your vehicle's mounting
area. Then use the supplied hardware
(Tapping Screw (5x25mm) and Plain
Washer) to attach the other end of
metal strap to a solid metal part of the
vehicle under the dashboard. This strap
also helps ensure proper electrical
grounding of the unit.

4

Sleeve

Dashboard

Screwdriver

Tabs

Spring Washer

Tapping Screw

Plain Washer

Hex Nut

Metal Strap

Mounting Bolt

INSTALLATION

Note:  to install the short threading terminal
of the mounting bolt to the back of the
unit and the other long threading terminal
to the dashboard.

9. Reconnect the cable to the vehicle

battery's negative (-) terminal.  Then
replace the outer trim ring.

Removing the unit

1. Make sure the ignition is turned off, 

then disconnect the cable from the 
vehicle battery's negative (-) terminal.

2. Remove the metal strap attached the

back of the unit (if attached).

3. Insert fingers into the groove in the 

right side of the outer trim ring and pull
out to remove it.  (You can also 
remove the outer trim ring from the left
side.)

4. After removing outer trim ring and

when the front panel is hidden, insert
both of the supplied keys into the slots
at the left and right  sides of the unit,
then pull the unit out of the
dashboard.

Outer Trim Ring

L Key

Sleeve

R Key

Summary of Contents for VBD1900MP





















Reviews: