Lantronix SM4T4DPA Install Manual Download Page 18

Lantronix  

 

 

SM4T4DPA Install Guide 

33867 Rev. A 

https://www.lantronix.com 

 

Page 

18

 of 

29

 

Making Network Connections 

Connecting Network Devices  

The switch is designed to be connected to 10, 100 or 1000Mbps network cards in PCs and servers, as well as to 
other switches and hubs. It may also be connected to remote devices using optional SFP transceivers.  

Twisted-Pair Devices 

Each device requires an unshielded twisted-pair (UTP) cable with RJ-45 connectors at both ends. Use Category 5, 
5e or 6 cable for 1000BASE-T connections, Category 5 or better for 100BASE-TX connections. 

Cabling Guidelines 

The RJ-45 ports on the switch support automatic MDI/MDI-X pinout configuration, so you can use standard straight-
through twisted-pair cables to connect to any other network device (PCs, servers, switches, routers, or hubs).  
See Appendix B for further information on cabling.  

Caution

: Do not plug a phone jack connector into an RJ-45 port. This will damage the switch. Use only twisted-pair 

cables with RJ-45 connectors that conform to FCC standards. 

Connecting to PCs, Servers, Hubs and Switches 

Step 1. Attach one end of a twisted-pair cable segment to the device’s RJ-45 connector.  

 

Making Twisted-Pair Connections 

Step 2. If the device is a network card and the switch is in the wiring closet, attach the other end of the cable 
segment to a modular wall outlet that is connected to the wiring closet. (See the section “Network Wiring 
Connections.”) Otherwise, attach the other end to an available port on the switch.  
Make sure each twisted pair cable does not exceed 100 meters (328 ft) in length.  

Note

: Avoid using flow control on a port connected to a hub unless it is actually required to solve a problem. 

Otherwise, back pressure jamming signals may degrade overall performance for the segment attached to  
the hub.  
Step 3. As each connection is made, the Link LED (on the switch) corresponding to each port will light green (1000 
Mbps) or amber (100 Mbps) to indicate that the connection is valid. 
 
 
 
 
 
 

Summary of Contents for SM4T4DPA






























Reviews: