Lantronix LFX2-MA Installation Manual Download

Page: 6 / 7

Declaration of Conformity

(according to ISO/IEC Guide 22 and EN 45014)

Manufacturer’s Name:

Lantronix

Manufacturer’s Address:

15353 Barranca Parkway
Irvine, CA 92618 USA

declares, that the product:

Product Name:

Ethernet Extender

Model Number(s):

LFX2-MA

conforms to the following standards:

Safety:

EN 60950:

1988 + A1, A2

EMC:

EN 55022:

1988 Class A

EN 50082-1:

1992

IEC 801-2:

1991/prEN55024-2:
1992-4kV CD, 8kV AD.

IEC 801-3:

1992/prEN55024-3: 1991-3V/m

IEC 801-4:

1988/prEN55024-4:
1992-.05kV Signal Lines
1kV Power Lines

Supplementary Information:

“The product complies with the requirements of the

Low Voltage Directive 73/23/EEC and the EMC Directive
89/336/EEC.”

Manufacturer’s Contact:

Director of Quality Assurance
Lantronix
15353 Barranca Parkway
Irvine, CA 92618 USA
Tel: 949-453-3990
Fax: 949-453-3995

15353 Barranca Parkway, Irvine, CA 92618

949-453-3990

▼

Fax: 949-453-3995

Direct Sales: 800-422-7055

▼

[email protected]

International Sales: 949-450-7227

▼

[email protected]

Tech Support: 800-422-7044

▼

[email protected]

www.lantronix.com

Part No. 900-1

Summary of Contents for LFX2-MA








Search results

Summary of Contents for LFX2-MA

Reviews:

Related manuals for LFX2-MA

Brands by name

Popular brands

Lantronix LFX2-MA, Installation Manual

Search results

Summary of Contents for LFX2-MA

Reviews:

Related manuals for LFX2-MA

Brands by name

Popular brands