Lantronix BOLERO40 Series Application Note Download Page 2

In-Vehicle Installation Guidelines for FOX3-2G/3G/4G and BOLERO40 Series 

Intellectual Property 

© 2019 Lantronix, Inc.  All rights reserved. No part of the contents of this publication may 
be transmitted or reproduced in any form or by any means without the written permission 
of Lantronix.  

Lantronix

 is a registered trademark of Lantronix, Inc. in the United States and other 

countries.   

Patented: 

www.lantronix.com/legal/patents/

; additional patents pending. 

All trademarks and trade names are the property of their respective holders.  

Contacts 

Lantronix, Inc. 

7535 Irvine Center Drive, Suite 100 
Irvine, CA 92618, USA 
Toll Free:  800-526-8766 
Phone:  

949-453-3990 

Fax:  

949-453-3995 

Technical Support

 

Online:  

www.lantronix.com/support

 

Sales Offices

 

For a current list of our domestic and international sales offices, go to the Lantronix web 
site at 

www.lantronix.com/about/contact

 

Disclaimer 

All information contained herein is provided “AS IS.”  Lantronix undertakes no obligation to 
update the information in this publication.  Lantronix does not make, and specifically 
disclaims, all warranties of any kind (express, implied or otherwise) regarding title, non-
infringement, fitness, quality, accuracy, completeness, usefulness, suitability or 
performance of the information provided herein. Lantronix shall have no liability 
whatsoever to any user for any damages, losses and causes of action (whether in contract 
or in tort or otherwise) in connection with the user’s access or usage of any of the 
information or content contained herein.  The information and specifications contained in 
this document are subject to change without notice. 

 

 

Summary of Contents for BOLERO40 Series





















Reviews: