Lantronix A5135-H User Manual Download Page 5 | Manualshive

Page: 5 / 33

Lantronix A5135-H User Manual Download Page 5

GNSS Receiver Module A5135-H User Guide

5

6.3 DC Electrical Characteristics ____________________________________________23

7.1 Proposed Footprint for Soldering ________________________________________24

7.2 PCB Design Guide ___________________________________________________24

7.3 Recommended Profile for Reflow Soldering ________________________________25

8 Use of External Antenna

8.1 Connection of RF Signal _______________________________________________26

8.2 External Antenna _____________________________________________________27

8.2.1 Recommended Parameters ________________________________________27

8.2.2 Hints __________________________________________________________27

9 Quality and Reliability

9.1 Environmental Conditions ______________________________________________28

9.2 Product Qualification __________________________________________________28

9.3 Production Test ______________________________________________________28

10 Applications and Hints

10.1 Initial Module Start ___________________________________________________29

10.2 Proper Shutdown ____________________________________________________29

Support ________________________________________________29

10.4 Push-to-Fix Mode ___________________________________________________29

10.5 Hibernate Mode _____________________________________________________29

10.6 Extended Ephemeris _________________________________________________30

10.7 TM_GPIO5 pin (1 pulse per second pin) __________________________________30

10.8 5 Hz Navigation Update Rate __________________________________________31

11 Evaluation Kit EVA5135-H

12 Related Information

12.1 Related Documents __________________________________________________33

12.2 Related Tools ______________________________________________________33

«
...
3
4
5
6
7
...
»

Summary of Contents for A5135-H


































Reviews:

No comments