background image

Lantronix

 

 

x6310 ION POTS Media Converter User Guide 

33818 Rev. A 

    

https://www.lantronix.com/

  

Page 

11

 of 

39

 

Installing the Chassis Model (C6310) 

The C6310 is a slide-in module that can only be installed in a Lantronix ION chassis (ION001-x, ION106-x, and 
ION219-x). This section describes how to install the C6310 in the ION chassis.  

 

 

Chassis Installation 

Important

:  The C6310 slide-in cards are “hot swappable” devices and can be removed and installed with chassis 

power on. 
1.  Locate an empty slot in the ION System chassis.  
2.  Grasp the edges of the card by its front panel. 
3.  Align the card with the upper and lower slot guides, and carefully insert the card into the slot. 
4.  Firmly seat the card against the chassis back panel. 
5.  Push in and rotate clockwise the panel fastener screw to secure the card to the chassis (see Chassis 

Installation figure above). 

6.  Note that the card’s Power LED lights.  

 

 

 

 

 

  

Caution

: Failure to wear a grounding device and observe electrostatic discharge precautions when 

installing the C6310 could result in damage or failure of the module.  

Summary of Contents for 6310 Series








































Reviews: