10
Motherboard Information
Chapter 3
Network Application Platforms
Jumper Settings
M1
VGA Interface (J1): It is for connecting the VGA
interface cable.
M2
USB Connector(J8) : It is for connecting the USB
module cable. It complies with USB2.0 and support
up to 480 Mbps connection speed.
M3
PCI-Ex8 Golden Finger(J1): It is for connecting the riser
card to add the expansion cards which might be an
AGP or RAID controller to the system. Refer to
for an installing illustration.
M4
AT Mode Power Button Connector (CONN1):It is for
connecting the power switch in AT mode in lieu of
the following jumper selections, ie, you don’t need to
adjust the AT/ATX Mode Selection or AT Mode jumper
settings.
M5
AT/ATX Mode Selection Jumper(J11): Please adjust
the jumpers (J10 and J11) respectively as described in
the following jumper settings when connecting the
power switch in AT mode.
M6
AT Mode Jumper(J10): It is for adjusting the jumper
setting for the power mode. Note that you have to
adjust the jumper J11 accordingly.
M7
CF Master/Slave Selection Jumper(J2): It is for selecting
the CF card as a master or slave drive. Note that the
default setting of J2 jumper is set to Master. Note that
this jumper only useful when there are other storage
devices such as a CD-ROM installed in the system
which is not applicable in the FW-7580.
Master
Slave
3
2
1
3
2
1
M8
CompactFlash Connector (CF1): It is for connecting
a Compact Flash card to be served as your system's
storage. For details of pin assignment, please refer to
the User's Manual.
M9
Keyboard and mouse interface Connectors(J16):
It is for connecting the PS/2 keyboard and mouse
interface cable.
M10
Front LCD Module Connector(J9): The 24-pin
connector is for connecting the front system panel.
M11
SPI-ROM Update Connector: Using the appropriate
cable to connect this 10-pin ISP in header connector,
the user can update the SPI Flash soldered on board.
M12
This connector is for the system power button.
Pressing the power button turns the system on or
puts the system in sleep or soft-off mode depending
on the BIOS settings.
M13
Hardware or Software Reset Jumper(JP2): The jumper
can be adjusted to be in either hardware or software
reset mode when the reset switch is pressed. The
hardware reset will reboot the system without turning
off the power. The software reset can be programmed
to reset a software to its default setting.
Function
USB_VCC
USBD- USBD+
GND
GND
PIN NO.
2
4
6
8
10
2 4 6 8 10
1 3 5 7 9
1 3 5 7 9 11
Function
GND
GND
GND
GND
GND
DDCCLK
PIN NO.
2
4
6
8
10
12
2 4 6 8 10 12
PIN NO.
1
3
5
7
9
11
Function
Red
Green
Blue
HSYNC
VSYNC D D C -
DATA
2
1
Pin No.
Function
--
AT mode
1-2
ATX mode (Default)
Pin No.
Function
--
Normal(Default)
1-2
AT mode
2 1
Pin No.
Function
VCC
1
MSDATA
3
KBDATA
5
GND
7
Pin No.
Function
2
MSCLK
4
KEY
6
KEY
8
KBCLK
1
3
5
7
2
4
6
8
Function
Pin No.
NC
1
ICH_SPI_CS0#
3
SB_SPI_MISO
5
KEY
7
GND
9
Pin No.
Function
2
NC
4
V_3P3_SPI_R
6
SPI_HD_N
8
ICH_SPI_CLK
10
ICH_SPI_MOSI
1
3
5
7
9
2
4
6
8
10
Pin No.
Function
1-2 (Default)
Software Reset
2-3
Hardware Reset
1
2
3
Pin No.
Pin name
1
PANSW
2
GND
1
2
PIN NO.
1
3
5
7
9
Function USB_VCC
USBD-
USBD+
GND
GND