manualshive.com logo in svg

Lanier R/C S.E.5A, User Manual, Page: 4 / 16

Share
Download
Lanier R/C S.E.5A User Manual Download Page 4

Installing Ailerons

1.

Collect the following parts:

(2) Wings

(4) Ailerons ( Left & Right)

(12) Mini CA hinges

2.

Locate the pre-cut aileron hinge slots in both

sides of the wing. Using a hobby knife (#11

blade), slide the blade into each slot to make

sure it is cleanly cut.

Repeat this process with the ailerons, making

sure all hinge slots are clean.

3.

Insert the mini CA hinges half way into the

wing and the ailerons. (Use a pin inserted into

the middle of the hinge to help keep the hinge

in the middle.) 

Make sure that the aileron is tight against the

wing and even with the wing tip.

Using thin CA glue, place one drop on all

hinges top and bottom.

Repeat for the other three ailerons.

Aileron Control Horns

1.

Gather the following items:

(6) Small Control Horns

(2) Wing

(2) EZ Connectors With Hardware

(2) Swivel Keeper

2.

Cut the back plate off the side of the control

horn.

3.

Locate the pre-drilled control hole holes in the

aileron. The control horn on the bottom side

faces toward the leading edge of the aileron.

The other control horn goes on the top side of

the aileron and faces the trailing edge.

Place glue on the control horn pins and insert

them in the holes.

Place the plate on the pins on the opposite

side and glue in place.

bottom side of bottom wing aileron

leading edge

4.

Install the two control horns on the top wing

ailerons on the bottom side facing the rear.

Installing Aileron Servos

1.

Gather the following items:

(2)12" Extension wires

(1) Bottom Wing

(2) Servos

(1) Electrical tape

(2) Servo spacers

Summary of Contents for S.E.5A

















Reviews:

No comments